[4/9] board: stm32: Add Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit
diff mbox series

Message ID 20210228155226.77904-5-jagan@amarulasolutions.com
State New
Headers show
Series
  • stm32: Add Engicam STM32MP1 SoM
Related show

Commit Message

Jagan Teki Feb. 28, 2021, 3:52 p.m. UTC 
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.

Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out

i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.

i.Core STM32MP1 needs to mount on top of this Evaluation board for
creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.

Add support for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
 arch/arm/dts/Makefile                         |   1 +
 ...mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi |  51 ++++++
 .../stm32mp157a-icore-stm32mp1-edimm2.2.dts   |  47 ++++++
 .../stm32mp157a-icore-stm32mp1-u-boot.dtsi    | 146 ++++++++++++++++++
 arch/arm/mach-stm32mp/Kconfig                 |  20 +++
 board/engicam/stm32mp1/Kconfig                |  12 ++
 board/engicam/stm32mp1/MAINTAINERS            |   6 +
 board/engicam/stm32mp1/Makefile               |  10 ++
 board/engicam/stm32mp1/spl.c                  |  48 ++++++
 board/engicam/stm32mp1/stm32mp1.c             | 131 ++++++++++++++++
 ...tm32mp15-icore-stm32mp1-edimm2.2_defconfig |  80 ++++++++++
 11 files changed, 552 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts
 create mode 100644 arch/arm/dts/stm32mp157a-icore-stm32mp1-u-boot.dtsi
 create mode 100644 board/engicam/stm32mp1/Kconfig
 create mode 100644 board/engicam/stm32mp1/MAINTAINERS
 create mode 100644 board/engicam/stm32mp1/Makefile
 create mode 100644 board/engicam/stm32mp1/spl.c
 create mode 100644 board/engicam/stm32mp1/stm32mp1.c
 create mode 100644 configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig

Comments

Patrice CHOTARD March 9, 2021, 2:04 p.m. UTC | #1 
Hi Jagan

one remark below

On 2/28/21 4:52 PM, Jagan Teki wrote:
> Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
> Evaluation Board.
> 
> Genaral features:
> - LCD 7" C.Touch
> - microSD slot
> - Ethernet 1Gb
> - Wifi/BT
> - 2x LVDS Full HD interfaces
> - 3x USB 2.0
> - 1x USB 3.0
> - HDMI Out
> - Mini PCIe
> - MIPI CSI
> - 2x CAN
> - Audio Out
> 
> i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
> 
> i.Core STM32MP1 needs to mount on top of this Evaluation board for
> creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.
> 
> Add support for it.
> 
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
>  arch/arm/dts/Makefile                         |   1 +
>  ...mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi |  51 ++++++
>  .../stm32mp157a-icore-stm32mp1-edimm2.2.dts   |  47 ++++++
>  .../stm32mp157a-icore-stm32mp1-u-boot.dtsi    | 146 ++++++++++++++++++
>  arch/arm/mach-stm32mp/Kconfig                 |  20 +++
>  board/engicam/stm32mp1/Kconfig                |  12 ++
>  board/engicam/stm32mp1/MAINTAINERS            |   6 +
>  board/engicam/stm32mp1/Makefile               |  10 ++
>  board/engicam/stm32mp1/spl.c                  |  48 ++++++
>  board/engicam/stm32mp1/stm32mp1.c             | 131 ++++++++++++++++
>  ...tm32mp15-icore-stm32mp1-edimm2.2_defconfig |  80 ++++++++++
>  11 files changed, 552 insertions(+)
>  create mode 100644 arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi
>  create mode 100644 arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts
>  create mode 100644 arch/arm/dts/stm32mp157a-icore-stm32mp1-u-boot.dtsi
>  create mode 100644 board/engicam/stm32mp1/Kconfig
>  create mode 100644 board/engicam/stm32mp1/MAINTAINERS
>  create mode 100644 board/engicam/stm32mp1/Makefile
>  create mode 100644 board/engicam/stm32mp1/spl.c
>  create mode 100644 board/engicam/stm32mp1/stm32mp1.c
>  create mode 100644 configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig
> 
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index f478f6f18f..f4a48c65e8 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -979,6 +979,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
>  dtb-$(CONFIG_STM32MP15x) += \
>  	stm32mp157a-dk1.dtb \
>  	stm32mp157a-avenger96.dtb \
> +	stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
>  	stm32mp157c-dk2.dtb \
>  	stm32mp157c-ed1.dtb \
>  	stm32mp157c-ev1.dtb \
> diff --git a/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi b/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi
> new file mode 100644
> index 0000000000..96fe461235
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi
> @@ -0,0 +1,51 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
> + * Copyright (c) 2020 Amarula Solutions(India)
> + * Author: Jagan Teki <jagan@amarulasolutions.com>
> + */
> +
> +#include "stm32mp157a-icore-stm32mp1-u-boot.dtsi"
> +
> +/{
> +	aliases {
> +		mmc0 = &sdmmc1;
> +	};
> +
> +	chosen {
> +		stdout-path = &uart4;
> +	};
> +};
> +
> +&sdmmc1 {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&sdmmc1_b4_pins_a {
> +	u-boot,dm-pre-reloc;
> +
> +	pins1 {
> +		u-boot,dm-pre-reloc;
> +	};
> +
> +	pins2 {
> +		u-boot,dm-pre-reloc;
> +	};
> +};
> +
> +&uart4 {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&uart4_pins_a {
> +	u-boot,dm-pre-reloc;
> +
> +	pins1 {
> +		u-boot,dm-pre-reloc;
> +	};
> +
> +	pins2 {
> +		u-boot,dm-pre-reloc;
> +		bias-pull-up;
> +	};
> +};
> diff --git a/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts b/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts
> new file mode 100644
> index 0000000000..ec9f1d1cd5
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts
> @@ -0,0 +1,47 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
> + * Copyright (c) 2020 Engicam srl
> + * Copyright (c) 2020 Amarula Solutons(India)
> + */
> +
> +/dts-v1/;
> +#include "stm32mp157.dtsi"
> +#include "stm32mp157a-icore-stm32mp1.dtsi"
> +#include "stm32mp15-pinctrl.dtsi"
> +#include "stm32mp15xxaa-pinctrl.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	model = "Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit";
> +	compatible = "engicam,icore-stm32mp1-edimm2.2",
> +		     "engicam,icore-stm32mp1", "st,stm32mp157";
> +
> +	aliases {
> +		serial0 = &uart4;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +};
> +
> +&sdmmc1 {
> +	bus-width = <4>;
> +	disable-wp;
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc1_b4_pins_a>;
> +	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> +	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> +	st,neg-edge;
> +	vmmc-supply = <&v3v3>;
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default", "sleep", "idle";
> +	pinctrl-0 = <&uart4_pins_a>;
> +	pinctrl-1 = <&uart4_sleep_pins_a>;
> +	pinctrl-2 = <&uart4_idle_pins_a>;
> +	status = "okay";
> +};
> diff --git a/arch/arm/dts/stm32mp157a-icore-stm32mp1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-icore-stm32mp1-u-boot.dtsi
> new file mode 100644
> index 0000000000..d62c24d4ce
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157a-icore-stm32mp1-u-boot.dtsi
> @@ -0,0 +1,146 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
> + * Copyright (c) 2020 Amarula Solutions(India)
> + * Author: Jagan Teki <jagan@amarulasolutions.com>
> + */
> +
> +#include <dt-bindings/clock/stm32mp1-clksrc.h>
> +#include "stm32mp15-u-boot.dtsi"
> +#include "stm32mp15-ddr3-icore-1x4Gb-1066-binG.dtsi"
> +
> +&vddcore {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&vdd {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&vdd_usb {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&vdda {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&vdd_ddr {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&vtt_ddr {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&vref_ddr {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&vdd_sd {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&v3v3 {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&v2v8 {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&v1v8 {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&rcc {
> +	st,clksrc = <
> +		CLK_MPU_PLL1P
> +		CLK_AXI_PLL2P
> +		CLK_MCU_PLL3P
> +		CLK_PLL12_HSE
> +		CLK_PLL3_HSE
> +		CLK_PLL4_HSE
> +		CLK_RTC_LSE
> +		CLK_MCO1_DISABLED
> +		CLK_MCO2_DISABLED
> +	>;
> +
> +	st,clkdiv = <
> +		1 /*MPU*/
> +		0 /*AXI*/
> +		0 /*MCU*/
> +		1 /*APB1*/
> +		1 /*APB2*/
> +		1 /*APB3*/
> +		1 /*APB4*/
> +		2 /*APB5*/
> +		23 /*RTC*/
> +		0 /*MCO1*/
> +		0 /*MCO2*/
> +	>;
> +
> +	st,pkcs = <
> +		CLK_CKPER_HSE
> +		CLK_FMC_ACLK
> +		CLK_QSPI_ACLK
> +		CLK_ETH_DISABLED
> +		CLK_SDMMC12_PLL4P
> +		CLK_DSI_DSIPLL
> +		CLK_STGEN_HSE
> +		CLK_USBPHY_HSE
> +		CLK_SPI2S1_PLL3Q
> +		CLK_SPI2S23_PLL3Q
> +		CLK_SPI45_HSI
> +		CLK_SPI6_HSI
> +		CLK_I2C46_HSI
> +		CLK_SDMMC3_PLL4P
> +		CLK_USBO_USBPHY
> +		CLK_ADC_CKPER
> +		CLK_CEC_LSE
> +		CLK_I2C12_HSI
> +		CLK_I2C35_HSI
> +		CLK_UART1_HSI
> +		CLK_UART24_HSI
> +		CLK_UART35_HSI
> +		CLK_UART6_HSI
> +		CLK_UART78_HSI
> +		CLK_SPDIF_PLL4P
> +		CLK_FDCAN_PLL4R
> +		CLK_SAI1_PLL3Q
> +		CLK_SAI2_PLL3Q
> +		CLK_SAI3_PLL3Q
> +		CLK_SAI4_PLL3Q
> +		CLK_RNG1_LSI
> +		CLK_RNG2_LSI
> +		CLK_LPTIM1_PCLK1
> +		CLK_LPTIM23_PCLK3
> +		CLK_LPTIM45_LSE
> +	>;
> +
> +	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
> +	pll2: st,pll@1 {
> +		compatible = "st,stm32mp1-pll";
> +		reg = <1>;
> +		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
> +		frac = < 0x1400 >;
> +		u-boot,dm-pre-reloc;
> +	};
> +
> +	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
> +	pll3: st,pll@2 {
> +		compatible = "st,stm32mp1-pll";
> +		reg = <2>;
> +		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
> +		frac = < 0x1a04 >;
> +		u-boot,dm-pre-reloc;
> +	};
> +
> +	/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
> +	pll4: st,pll@3 {
> +		compatible = "st,stm32mp1-pll";
> +		reg = <3>;
> +		cfg = < 3 98 5 7 7 PQR(1,1,1) >;
> +		u-boot,dm-pre-reloc;
> +	};
> +};
> diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig
> index 79ffd5191d..5a2123063a 100644
> --- a/arch/arm/mach-stm32mp/Kconfig
> +++ b/arch/arm/mach-stm32mp/Kconfig
> @@ -77,6 +77,25 @@ config TARGET_ST_STM32MP15x
>  		Evalulation board (EV1) or Discovery board (DK1 and DK2).
>  		The difference between board are managed with devicetree
>  
> +config TARGET_ICORE_STM32MP1
> +	bool "Engicam i.Core STM32MP1 SOM"
> +	select STM32MP15x
> +	imply BOOTCOUNT_LIMIT
> +	imply BOOTSTAGE
> +	imply CMD_BOOTCOUNT
> +	imply CMD_BOOTSTAGE
> +	imply CMD_CLS if CMD_BMP
> +	imply DISABLE_CONSOLE
> +	imply PRE_CONSOLE_BUFFER
> +	imply SILENT_CONSOLE
> +	help
> +	  i.Core STM32MP1 is an EDIMM SOM based on STM32MP157A.
> +
> +	  i.Core STM32MP1 EDIMM2.2:
> +	  * EDIMM2.2 is a Form Factor Capacitive Evaluation Board.
> +	  * i.Core STM32MP1 needs to mount on top of EDIMM2.2 for
> +	    creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.
> +
>  config TARGET_DH_STM32MP1_PDK2
>  	bool "DH STM32MP1 PDK2"
>  	select STM32MP15x
> @@ -177,6 +196,7 @@ config DEBUG_UART_CLOCK
>  	default 64000000
>  endif
>  
> +source "board/engicam/stm32mp1/Kconfig"
>  source "board/st/stm32mp1/Kconfig"
>  source "board/dhelectronics/dh_stm32mp1/Kconfig"
>  
> diff --git a/board/engicam/stm32mp1/Kconfig b/board/engicam/stm32mp1/Kconfig
> new file mode 100644
> index 0000000000..e7bccc09fb
> --- /dev/null
> +++ b/board/engicam/stm32mp1/Kconfig
> @@ -0,0 +1,12 @@
> +if TARGET_ICORE_STM32MP1
> +
> +config SYS_BOARD
> +	default "stm32mp1"
> +
> +config SYS_VENDOR
> +	default "engicam"
> +
> +config SYS_CONFIG_NAME
> +	default "stm32mp1"
> +
> +endif
> diff --git a/board/engicam/stm32mp1/MAINTAINERS b/board/engicam/stm32mp1/MAINTAINERS
> new file mode 100644
> index 0000000000..3230a7a6e8
> --- /dev/null
> +++ b/board/engicam/stm32mp1/MAINTAINERS
> @@ -0,0 +1,6 @@
> +i.Core-STM32MP1-EDIMM2.2
> +M:	Jagan Teki <jagan@amarulasolutions.com>
> +M:	Matteo Lisi <matteo.lisi@engicam.com>
> +S:	Maintained
> +F:	board/engicam/stm32mp1
> +F:	configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig
> diff --git a/board/engicam/stm32mp1/Makefile b/board/engicam/stm32mp1/Makefile
> new file mode 100644
> index 0000000000..65560df290
> --- /dev/null
> +++ b/board/engicam/stm32mp1/Makefile
> @@ -0,0 +1,10 @@
> +# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +#
> +# Copyright (C) 2018, STMicroelectronics - All Rights Reserved
> +#
> +
> +ifdef CONFIG_SPL_BUILD
> +obj-y += spl.o
> +else
> +obj-y += stm32mp1.o
> +endif
> diff --git a/board/engicam/stm32mp1/spl.c b/board/engicam/stm32mp1/spl.c
> new file mode 100644
> index 0000000000..79adb5f529
> --- /dev/null
> +++ b/board/engicam/stm32mp1/spl.c
> @@ -0,0 +1,48 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
> + * Copyright (C) 2020 Engicam S.r.l.
> + * Copyright (C) 2020 Amarula Solutions(India)
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +
> +/* board early initialisation in board_f: need to use global variable */
> +static u32 opp_voltage_mv __section(".data");
> +
> +void board_vddcore_init(u32 voltage_mv)
> +{
> +	if (IS_ENABLED(CONFIG_PMIC_STPMIC1) && CONFIG_IS_ENABLED(POWER_SUPPORT))
> +		opp_voltage_mv = voltage_mv;
> +}
> +
> +int board_early_init_f(void)
> +{
> +	return 0;
> +}
> +
> +#ifdef CONFIG_DEBUG_UART_BOARD_INIT
> +void board_debug_uart_init(void)
> +{
> +#if (CONFIG_DEBUG_UART_BASE == STM32_UART4_BASE)
> +
> +#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00)
> +#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28)
> +
> +	/* UART4 clock enable */
> +	setbits_le32(RCC_MP_APB1ENSETR, BIT(16));
> +
> +#define GPIOG_BASE 0x50008000
> +	/* GPIOG clock enable */
> +	writel(BIT(6), RCC_MP_AHB4ENSETR);
> +	/* GPIO configuration for ST boards: Uart4 TX = G11 */
> +	writel(0xffbfffff, GPIOG_BASE + 0x00);
> +	writel(0x00006000, GPIOG_BASE + 0x24);
> +#else
> +
> +#error("CONFIG_DEBUG_UART_BASE: not supported value")
> +
> +#endif
> +}
> +#endif
> diff --git a/board/engicam/stm32mp1/stm32mp1.c b/board/engicam/stm32mp1/stm32mp1.c
> new file mode 100644
> index 0000000000..2bd71a8fd7
> --- /dev/null
> +++ b/board/engicam/stm32mp1/stm32mp1.c
> @@ -0,0 +1,131 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
> + * Copyright (C) 2020 Engicam S.r.l.
> + * Copyright (C) 2020 Amarula Solutions(India)
> + * Author: Jagan Teki <jagan@amarulasolutions.com>
> + */
> +
> +#include <common.h>
> +#include <env.h>
> +#include <env_internal.h>
> +#include <syscon.h>
> +#include <asm/io.h>
> +#include <asm/arch/sys_proto.h>
> +#include <power/regulator.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int board_early_init_f(void)
> +{
> +	/* nothing to do, only used in SPL */
> +	return 0;
> +}

As board_early_init_f() is empty here and also in /board/engicam/stm32mp1/spl.c, it can be removed
and compilation flag CONFIG_BOARD_EARLY_INIT_F as well.

Patrice

> +
> +int checkboard(void)
> +{
> +	char *mode;
> +	const char *fdt_compat;
> +	int fdt_compat_len;
> +
> +	if (IS_ENABLED(CONFIG_TFABOOT))
> +		mode = "trusted";
> +	else
> +		mode = "basic";
> +
> +	printf("Board: stm32mp1 in %s mode", mode);
> +	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
> +				 &fdt_compat_len);
> +	if (fdt_compat && fdt_compat_len)
> +		printf(" (%s)", fdt_compat);
> +	puts("\n");
> +
> +	return 0;
> +}
> +
> +/* board dependent setup after realloc */
> +int board_init(void)
> +{
> +	/* address of boot parameters */
> +	gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
> +
> +	if (IS_ENABLED(CONFIG_DM_REGULATOR))
> +		regulators_enable_boot_on(_DEBUG);
> +
> +	return 0;
> +}
> +
> +int board_late_init(void)
> +{
> +	return 0;
> +}
> +
> +enum env_location env_get_location(enum env_operation op, int prio)
> +{
> +	u32 bootmode = get_bootmode();
> +
> +	if (prio)
> +		return ENVL_UNKNOWN;
> +
> +	switch (bootmode & TAMP_BOOT_DEVICE_MASK) {
> +	case BOOT_FLASH_SD:
> +	case BOOT_FLASH_EMMC:
> +		if (CONFIG_IS_ENABLED(ENV_IS_IN_MMC))
> +			return ENVL_MMC;
> +		else if (CONFIG_IS_ENABLED(ENV_IS_IN_EXT4))
> +			return ENVL_EXT4;
> +		else
> +			return ENVL_NOWHERE;
> +
> +	case BOOT_FLASH_NAND:
> +	case BOOT_FLASH_SPINAND:
> +		if (CONFIG_IS_ENABLED(ENV_IS_IN_UBI))
> +			return ENVL_UBI;
> +		else
> +			return ENVL_NOWHERE;
> +
> +	case BOOT_FLASH_NOR:
> +		if (CONFIG_IS_ENABLED(ENV_IS_IN_SPI_FLASH))
> +			return ENVL_SPI_FLASH;
> +		else
> +			return ENVL_NOWHERE;
> +
> +	default:
> +		return ENVL_NOWHERE;
> +	}
> +}
> +
> +const char *env_ext4_get_intf(void)
> +{
> +	u32 bootmode = get_bootmode();
> +
> +	switch (bootmode & TAMP_BOOT_DEVICE_MASK) {
> +	case BOOT_FLASH_SD:
> +	case BOOT_FLASH_EMMC:
> +		return "mmc";
> +	default:
> +		return "";
> +	}
> +}
> +
> +const char *env_ext4_get_dev_part(void)
> +{
> +	static char *const dev_part[] = {"0:auto", "1:auto", "2:auto"};
> +	u32 bootmode = get_bootmode();
> +
> +	return dev_part[(bootmode & TAMP_BOOT_INSTANCE_MASK) - 1];
> +}
> +
> +int mmc_get_env_dev(void)
> +{
> +	u32 bootmode = get_bootmode();
> +
> +	return (bootmode & TAMP_BOOT_INSTANCE_MASK) - 1;
> +}
> +
> +#if defined(CONFIG_OF_BOARD_SETUP)
> +int ft_board_setup(void *blob, struct bd_info *bd)
> +{
> +	return 0;
> +}
> +#endif
> diff --git a/configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig b/configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig
> new file mode 100644
> index 0000000000..48cf207f4c
> --- /dev/null
> +++ b/configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig
> @@ -0,0 +1,80 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_STM32MP=y
> +CONFIG_SYS_MALLOC_F_LEN=0x3000
> +CONFIG_SYS_MEMTEST_START=0xc0000000
> +CONFIG_SYS_MEMTEST_END=0xc4000000
> +CONFIG_ENV_OFFSET=0x280000
> +CONFIG_SPL_TEXT_BASE=0x2FFC2500
> +CONFIG_SPL_MMC_SUPPORT=y
> +CONFIG_SPL=y
> +CONFIG_TARGET_ICORE_STM32MP1=y
> +CONFIG_ENV_OFFSET_REDUND=0x2C0000
> +# CONFIG_ARMV7_VIRT is not set
> +CONFIG_DEFAULT_DEVICE_TREE="stm32mp157a-icore-stm32mp1-edimm2.2"
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_FIT=y
> +CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
> +CONFIG_BOARD_EARLY_INIT_F=y
> +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
> +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
> +CONFIG_SPL_ENV_SUPPORT=y
> +CONFIG_SPL_I2C_SUPPORT=y
> +CONFIG_SPL_POWER_SUPPORT=y
> +CONFIG_SYS_PROMPT="STM32MP> "
> +CONFIG_CMD_ADTIMG=y
> +CONFIG_CMD_ERASEENV=y
> +CONFIG_CMD_MEMINFO=y
> +CONFIG_CMD_MEMTEST=y
> +CONFIG_CMD_ADC=y
> +CONFIG_CMD_CLK=y
> +CONFIG_CMD_FUSE=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_REMOTEPROC=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_TIMER=y
> +CONFIG_CMD_PMIC=y
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_CMD_EXT4_WRITE=y
> +# CONFIG_SPL_DOS_PARTITION is not set
> +CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
> +CONFIG_ENV_IS_NOWHERE=y
> +CONFIG_ENV_IS_IN_MMC=y
> +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +# CONFIG_SPL_ENV_IS_NOWHERE is not set
> +CONFIG_DM_HWSPINLOCK=y
> +CONFIG_HWSPINLOCK_STM32=y
> +CONFIG_DM_I2C=y
> +CONFIG_SYS_I2C_STM32F7=y
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> +CONFIG_DM_MAILBOX=y
> +CONFIG_STM32_IPCC=y
> +CONFIG_STM32_FMC2_EBI=y
> +CONFIG_DM_MMC=y
> +CONFIG_SUPPORT_EMMC_BOOT=y
> +CONFIG_STM32_SDMMC2=y
> +CONFIG_PHY_REALTEK=y
> +CONFIG_DM_ETH=y
> +CONFIG_DWC_ETH_QOS=y
> +CONFIG_PHY=y
> +CONFIG_PINCONF=y
> +# CONFIG_SPL_PINCTRL_FULL is not set
> +CONFIG_PINCTRL_STMFX=y
> +CONFIG_DM_PMIC=y
> +# CONFIG_SPL_PMIC_CHILDREN is not set
> +CONFIG_PMIC_STPMIC1=y
> +CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_REGULATOR_GPIO=y
> +CONFIG_REMOTEPROC_STM32_COPRO=y
> +CONFIG_DM_RTC=y
> +CONFIG_RTC_STM32=y
> +CONFIG_SERIAL_RX_BUFFER=y
> +CONFIG_WDT=y
> +CONFIG_WDT_STM32MP=y
> +CONFIG_LZO=y
> +CONFIG_ERRNO_STR=y
>

Patch
diff mbox series 

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index f478f6f18f..f4a48c65e8 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -979,6 +979,7 @@  dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157a-dk1.dtb \
 	stm32mp157a-avenger96.dtb \
+	stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
diff --git a/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi b/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi
new file mode 100644
index 0000000000..96fe461235
--- /dev/null
+++ b/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2-u-boot.dtsi
@@ -0,0 +1,51 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Amarula Solutions(India)
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+#include "stm32mp157a-icore-stm32mp1-u-boot.dtsi"
+
+/{
+	aliases {
+		mmc0 = &sdmmc1;
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+};
+
+&sdmmc1 {
+	u-boot,dm-pre-reloc;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-pre-reloc;
+
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+
+	pins2 {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+
+	pins2 {
+		u-boot,dm-pre-reloc;
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts b/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts
new file mode 100644
index 0000000000..ec9f1d1cd5
--- /dev/null
+++ b/arch/arm/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts
@@ -0,0 +1,47 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutons(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-icore-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit";
+	compatible = "engicam,icore-stm32mp1-edimm2.2",
+		     "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/stm32mp157a-icore-stm32mp1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-icore-stm32mp1-u-boot.dtsi
new file mode 100644
index 0000000000..d62c24d4ce
--- /dev/null
+++ b/arch/arm/dts/stm32mp157a-icore-stm32mp1-u-boot.dtsi
@@ -0,0 +1,146 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Amarula Solutions(India)
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp15-u-boot.dtsi"
+#include "stm32mp15-ddr3-icore-1x4Gb-1066-binG.dtsi"
+
+&vddcore {
+	u-boot,dm-pre-reloc;
+};
+
+&vdd {
+	u-boot,dm-pre-reloc;
+};
+
+&vdd_usb {
+	u-boot,dm-pre-reloc;
+};
+
+&vdda {
+	u-boot,dm-pre-reloc;
+};
+
+&vdd_ddr {
+	u-boot,dm-pre-reloc;
+};
+
+&vtt_ddr {
+	u-boot,dm-pre-reloc;
+};
+
+&vref_ddr {
+	u-boot,dm-pre-reloc;
+};
+
+&vdd_sd {
+	u-boot,dm-pre-reloc;
+};
+
+&v3v3 {
+	u-boot,dm-pre-reloc;
+};
+
+&v2v8 {
+	u-boot,dm-pre-reloc;
+};
+
+&v1v8 {
+	u-boot,dm-pre-reloc;
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_DISABLED
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4R
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll@1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll@2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
+	pll4: st,pll@3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
+		cfg = < 3 98 5 7 7 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig
index 79ffd5191d..5a2123063a 100644
--- a/arch/arm/mach-stm32mp/Kconfig
+++ b/arch/arm/mach-stm32mp/Kconfig
@@ -77,6 +77,25 @@  config TARGET_ST_STM32MP15x
 		Evalulation board (EV1) or Discovery board (DK1 and DK2).
 		The difference between board are managed with devicetree
 
+config TARGET_ICORE_STM32MP1
+	bool "Engicam i.Core STM32MP1 SOM"
+	select STM32MP15x
+	imply BOOTCOUNT_LIMIT
+	imply BOOTSTAGE
+	imply CMD_BOOTCOUNT
+	imply CMD_BOOTSTAGE
+	imply CMD_CLS if CMD_BMP
+	imply DISABLE_CONSOLE
+	imply PRE_CONSOLE_BUFFER
+	imply SILENT_CONSOLE
+	help
+	  i.Core STM32MP1 is an EDIMM SOM based on STM32MP157A.
+
+	  i.Core STM32MP1 EDIMM2.2:
+	  * EDIMM2.2 is a Form Factor Capacitive Evaluation Board.
+	  * i.Core STM32MP1 needs to mount on top of EDIMM2.2 for
+	    creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.
+
 config TARGET_DH_STM32MP1_PDK2
 	bool "DH STM32MP1 PDK2"
 	select STM32MP15x
@@ -177,6 +196,7 @@  config DEBUG_UART_CLOCK
 	default 64000000
 endif
 
+source "board/engicam/stm32mp1/Kconfig"
 source "board/st/stm32mp1/Kconfig"
 source "board/dhelectronics/dh_stm32mp1/Kconfig"
 
diff --git a/board/engicam/stm32mp1/Kconfig b/board/engicam/stm32mp1/Kconfig
new file mode 100644
index 0000000000..e7bccc09fb
--- /dev/null
+++ b/board/engicam/stm32mp1/Kconfig
@@ -0,0 +1,12 @@ 
+if TARGET_ICORE_STM32MP1
+
+config SYS_BOARD
+	default "stm32mp1"
+
+config SYS_VENDOR
+	default "engicam"
+
+config SYS_CONFIG_NAME
+	default "stm32mp1"
+
+endif
diff --git a/board/engicam/stm32mp1/MAINTAINERS b/board/engicam/stm32mp1/MAINTAINERS
new file mode 100644
index 0000000000..3230a7a6e8
--- /dev/null
+++ b/board/engicam/stm32mp1/MAINTAINERS
@@ -0,0 +1,6 @@ 
+i.Core-STM32MP1-EDIMM2.2
+M:	Jagan Teki <jagan@amarulasolutions.com>
+M:	Matteo Lisi <matteo.lisi@engicam.com>
+S:	Maintained
+F:	board/engicam/stm32mp1
+F:	configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig
diff --git a/board/engicam/stm32mp1/Makefile b/board/engicam/stm32mp1/Makefile
new file mode 100644
index 0000000000..65560df290
--- /dev/null
+++ b/board/engicam/stm32mp1/Makefile
@@ -0,0 +1,10 @@ 
+# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+#
+# Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
+obj-y += stm32mp1.o
+endif
diff --git a/board/engicam/stm32mp1/spl.c b/board/engicam/stm32mp1/spl.c
new file mode 100644
index 0000000000..79adb5f529
--- /dev/null
+++ b/board/engicam/stm32mp1/spl.c
@@ -0,0 +1,48 @@ 
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2020 Engicam S.r.l.
+ * Copyright (C) 2020 Amarula Solutions(India)
+ */
+
+#include <common.h>
+#include <asm/io.h>
+
+/* board early initialisation in board_f: need to use global variable */
+static u32 opp_voltage_mv __section(".data");
+
+void board_vddcore_init(u32 voltage_mv)
+{
+	if (IS_ENABLED(CONFIG_PMIC_STPMIC1) && CONFIG_IS_ENABLED(POWER_SUPPORT))
+		opp_voltage_mv = voltage_mv;
+}
+
+int board_early_init_f(void)
+{
+	return 0;
+}
+
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
+{
+#if (CONFIG_DEBUG_UART_BASE == STM32_UART4_BASE)
+
+#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00)
+#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28)
+
+	/* UART4 clock enable */
+	setbits_le32(RCC_MP_APB1ENSETR, BIT(16));
+
+#define GPIOG_BASE 0x50008000
+	/* GPIOG clock enable */
+	writel(BIT(6), RCC_MP_AHB4ENSETR);
+	/* GPIO configuration for ST boards: Uart4 TX = G11 */
+	writel(0xffbfffff, GPIOG_BASE + 0x00);
+	writel(0x00006000, GPIOG_BASE + 0x24);
+#else
+
+#error("CONFIG_DEBUG_UART_BASE: not supported value")
+
+#endif
+}
+#endif
diff --git a/board/engicam/stm32mp1/stm32mp1.c b/board/engicam/stm32mp1/stm32mp1.c
new file mode 100644
index 0000000000..2bd71a8fd7
--- /dev/null
+++ b/board/engicam/stm32mp1/stm32mp1.c
@@ -0,0 +1,131 @@ 
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2020 Engicam S.r.l.
+ * Copyright (C) 2020 Amarula Solutions(India)
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+#include <common.h>
+#include <env.h>
+#include <env_internal.h>
+#include <syscon.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <power/regulator.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	/* nothing to do, only used in SPL */
+	return 0;
+}
+
+int checkboard(void)
+{
+	char *mode;
+	const char *fdt_compat;
+	int fdt_compat_len;
+
+	if (IS_ENABLED(CONFIG_TFABOOT))
+		mode = "trusted";
+	else
+		mode = "basic";
+
+	printf("Board: stm32mp1 in %s mode", mode);
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len)
+		printf(" (%s)", fdt_compat);
+	puts("\n");
+
+	return 0;
+}
+
+/* board dependent setup after realloc */
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
+
+	if (IS_ENABLED(CONFIG_DM_REGULATOR))
+		regulators_enable_boot_on(_DEBUG);
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	return 0;
+}
+
+enum env_location env_get_location(enum env_operation op, int prio)
+{
+	u32 bootmode = get_bootmode();
+
+	if (prio)
+		return ENVL_UNKNOWN;
+
+	switch (bootmode & TAMP_BOOT_DEVICE_MASK) {
+	case BOOT_FLASH_SD:
+	case BOOT_FLASH_EMMC:
+		if (CONFIG_IS_ENABLED(ENV_IS_IN_MMC))
+			return ENVL_MMC;
+		else if (CONFIG_IS_ENABLED(ENV_IS_IN_EXT4))
+			return ENVL_EXT4;
+		else
+			return ENVL_NOWHERE;
+
+	case BOOT_FLASH_NAND:
+	case BOOT_FLASH_SPINAND:
+		if (CONFIG_IS_ENABLED(ENV_IS_IN_UBI))
+			return ENVL_UBI;
+		else
+			return ENVL_NOWHERE;
+
+	case BOOT_FLASH_NOR:
+		if (CONFIG_IS_ENABLED(ENV_IS_IN_SPI_FLASH))
+			return ENVL_SPI_FLASH;
+		else
+			return ENVL_NOWHERE;
+
+	default:
+		return ENVL_NOWHERE;
+	}
+}
+
+const char *env_ext4_get_intf(void)
+{
+	u32 bootmode = get_bootmode();
+
+	switch (bootmode & TAMP_BOOT_DEVICE_MASK) {
+	case BOOT_FLASH_SD:
+	case BOOT_FLASH_EMMC:
+		return "mmc";
+	default:
+		return "";
+	}
+}
+
+const char *env_ext4_get_dev_part(void)
+{
+	static char *const dev_part[] = {"0:auto", "1:auto", "2:auto"};
+	u32 bootmode = get_bootmode();
+
+	return dev_part[(bootmode & TAMP_BOOT_INSTANCE_MASK) - 1];
+}
+
+int mmc_get_env_dev(void)
+{
+	u32 bootmode = get_bootmode();
+
+	return (bootmode & TAMP_BOOT_INSTANCE_MASK) - 1;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+	return 0;
+}
+#endif
diff --git a/configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig b/configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig
new file mode 100644
index 0000000000..48cf207f4c
--- /dev/null
+++ b/configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig
@@ -0,0 +1,80 @@ 
+CONFIG_ARM=y
+CONFIG_ARCH_STM32MP=y
+CONFIG_SYS_MALLOC_F_LEN=0x3000
+CONFIG_SYS_MEMTEST_START=0xc0000000
+CONFIG_SYS_MEMTEST_END=0xc4000000
+CONFIG_ENV_OFFSET=0x280000
+CONFIG_SPL_TEXT_BASE=0x2FFC2500
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_TARGET_ICORE_STM32MP1=y
+CONFIG_ENV_OFFSET_REDUND=0x2C0000
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_DEFAULT_DEVICE_TREE="stm32mp157a-icore-stm32mp1-edimm2.2"
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
+CONFIG_SPL_ENV_SUPPORT=y
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SYS_PROMPT="STM32MP> "
+CONFIG_CMD_ADTIMG=y
+CONFIG_CMD_ERASEENV=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_ADC=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_REMOTEPROC=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
+CONFIG_ENV_IS_NOWHERE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+# CONFIG_SPL_ENV_IS_NOWHERE is not set
+CONFIG_DM_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_STM32=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_STM32F7=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_DM_MAILBOX=y
+CONFIG_STM32_IPCC=y
+CONFIG_STM32_FMC2_EBI=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_STM32_SDMMC2=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_ETH=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_PHY=y
+CONFIG_PINCONF=y
+# CONFIG_SPL_PINCTRL_FULL is not set
+CONFIG_PINCTRL_STMFX=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_PMIC_STPMIC1=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_REMOTEPROC_STM32_COPRO=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_STM32=y
+CONFIG_SERIAL_RX_BUFFER=y
+CONFIG_WDT=y
+CONFIG_WDT_STM32MP=y
+CONFIG_LZO=y
+CONFIG_ERRNO_STR=y