@@ -5,6 +5,8 @@
config SIFIVE_FU540
bool
select ARCH_EARLY_INIT_R
+ imply BOARD
+ imply BOARD_FU540
imply CPU
imply CPU_RISCV
imply RISCV_TIMER
@@ -12,6 +12,10 @@
spi2 = &qspi2;
};
+ config {
+ u-boot,spl-payload-offset = <0x105000>; /* loader2 @1044KB */
+ };
+
hfclk {
u-boot,dm-spl;
};
@@ -22,6 +26,14 @@
};
+&qspi0 {
+ u-boot,dm-spl;
+
+ flash@0 {
+ u-boot,dm-spl;
+ };
+};
+
&qspi2 {
mmc@0 {
u-boot,dm-spl;
@@ -116,18 +116,6 @@ int board_init(void)
return 0;
}
-#ifdef CONFIG_SPL
-u32 spl_boot_device(void)
-{
-#ifdef CONFIG_SPL_MMC_SUPPORT
- return BOOT_DEVICE_MMC1;
-#else
- puts("Unknown boot device\n");
- hang();
-#endif
-}
-#endif
-
#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
@@ -2,9 +2,11 @@ CONFIG_RISCV=y
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x3000
CONFIG_ENV_SIZE=0x20000
+CONFIG_SPL_DM_SPI=y
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
CONFIG_TARGET_SIFIVE_FU540=y
CONFIG_ARCH_RV64I=y
@@ -15,9 +17,11 @@ CONFIG_MISC_INIT_R=y
CONFIG_DISPLAY_CPUINFO=y
CONFIG_DISPLAY_BOARDINFO=y
CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_SPI_LOAD=y
CONFIG_SPL_YMODEM_SUPPORT=y
CONFIG_OF_BOARD_FIXUP=y
CONFIG_DEFAULT_DEVICE_TREE="hifive-unleashed-a00"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_SPL_CLK=y
CONFIG_DM_MTD=y
@@ -541,3 +541,44 @@ Sample boot log from HiFive Unleashed board
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 9faa81b6-39b1-4418-af5e-89c48f29c20d
+
+Booting from SPI
+----------------
+
+Use Building steps from "Booting from MMC using U-Boot SPL" section.
+
+Partition the SPI in Linux via mtdblock. (Require to boot the board in
+SD boot mode by enabling MTD block in Linux)
+
+Use prebuilt image from here [1], which support to partition the SPI flash.
+
+.. code-block:: none
+
+ # sgdisk --clear \
+ > --set-alignment=2 \
+ > --new=1:40:2087 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
+ > --new=2:2088:10279 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
+ > --new=3:10536:65494 --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
+ > /dev/mtdblock0
+
+Program the SPI (Require to boot the board in SD boot mode)
+
+Execute below steps on U-Boot proper,
+
+.. code-block:: none
+
+ sf erase 0x5000 0x100000
+ tftpboot $kernel_addr_r u-boot-spl.bin
+ sf write $kernel_addr_r 0x5000 $filesize
+
+ sf erase 0x105000 0x100000
+ tftpboot $kernel_addr_r u-boot.itb
+ sf write $kernel_addr_r 0x105000 $filesize
+
+Power off the board
+
+Change DIP switches MSEL[3:0] are set to 0110
+
+Power up the board.
+
+[1] https://github.com/amarula/bsp-sifive
U-Boot SPL 2020.07-rc2-00156-gb9abb0716a-dirty (May 19 2020 - 21:56:17 +0530) Trying to boot from SPI U-Boot 2020.07-rc2-00156-gb9abb0716a-dirty (May 19 2020 - 21:56:17 +0530) CPU: rv64imafdc Model: SiFive HiFive Unleashed A00 DRAM: 8 GiB No reserved memory region found in source FDT MMC: spi@10050000:mmc@0: 0 In: serial@10010000 Out: serial@10010000 Err: serial@10010000 Net: eth0: ethernet@10090000 Hit any key to stop autoboot: 0 Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- Changes for v2: - enable board driver - comment spl-payloade-offset - reference for SPI partition arch/riscv/cpu/fu540/Kconfig | 2 + .../dts/hifive-unleashed-a00-u-boot.dtsi | 12 ++++++ board/sifive/fu540/fu540.c | 12 ------ configs/sifive_fu540_defconfig | 4 ++ doc/board/sifive/fu540.rst | 41 +++++++++++++++++++ 5 files changed, 59 insertions(+), 12 deletions(-)