@@ -1599,7 +1599,6 @@ source "board/freescale/mpc8572ds/Kconfig"
source "board/freescale/p1023rdb/Kconfig"
source "board/freescale/p1_twr/Kconfig"
source "board/freescale/qemu-ppce500/Kconfig"
-source "board/freescale/t208xrdb/Kconfig"
source "board/freescale/t4qds/Kconfig"
source "board/freescale/t4rdb/Kconfig"
source "board/gdsys/p1022/Kconfig"
deleted file mode 100644
@@ -1,14 +0,0 @@
-if TARGET_T2080RDB
-
-config SYS_BOARD
- default "t208xrdb"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "T208xRDB"
-
-source "board/freescale/common/Kconfig"
-
-endif
deleted file mode 100644
@@ -1,15 +0,0 @@
-T208XRDB BOARD
-M: Shengzhou Liu <Shengzhou.Liu@nxp.com>
-S: Maintained
-F: board/freescale/t208xrdb/
-F: include/configs/T208xRDB.h
-F: configs/T2080RDB_defconfig
-F: configs/T2080RDB_NAND_defconfig
-F: configs/T2080RDB_SDCARD_defconfig
-F: configs/T2080RDB_SPIFLASH_defconfig
-F: configs/T2080RDB_SRIO_PCIE_BOOT_defconfig
-
-T2080RDB_SECURE_BOOT BOARD
-M: Ruchika Gupta <ruchika.gupta@nxp.com>
-S: Maintained
-F: configs/T2080RDB_SECURE_BOOT_defconfig
deleted file mode 100644
@@ -1,16 +0,0 @@
-#
-# Copyright 2014 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-ifdef CONFIG_SPL_BUILD
-obj-y += spl.o
-else
-obj-$(CONFIG_TARGET_T2080RDB) += t208xrdb.o eth_t208xrdb.o cpld.o
-obj-$(CONFIG_PCI) += pci.o
-endif
-
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
deleted file mode 100644
@@ -1,283 +0,0 @@
-T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
-It can work in two mode: standalone mode and PCIe endpoint mode.
-
-T2080 SoC Overview
-------------------
-The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power
-Architecture processor cores with high-performance datapath acceleration
-logic and network and peripheral bus interfaces required for networking,
-telecom/datacom, wireless infrastructure, and mil/aerospace applications.
-
-T2080 includes the following functions and features:
- - Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- - 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- - Hierarchical interconnect fabric
- - One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- - Data Path Acceleration Architecture (DPAA) incorporating acceleration
- - 16 SerDes lanes up to 10.3125 GHz
- - 8 Ethernet interfaces, supporting combinations of the following:
- - Up to four 10 Gbps Ethernet MACs
- - Up to eight 1 Gbps Ethernet MACs
- - Up to four 2.5 Gbps Ethernet MACs
- - High-speed peripheral interfaces
- - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- - Additional peripheral interfaces
- - Two serial ATA (SATA 2.0) controllers
- - Two high-speed USB 2.0 controllers with integrated PHY
- - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
- - Enhanced serial peripheral interface (eSPI)
- - Four I2C controllers
- - Four 2-pin UARTs or two 4-pin UARTs
- - Integrated Flash Controller supporting NAND and NOR flash
- - Three eight-channel DMA engines
- - Support for hardware virtualization and partitioning enforcement
- - QorIQ Platform's Trust Architecture 2.0
-
-Differences between T2080 and T2081
------------------------------------
- Feature T2080 T2081
- 1G Ethernet numbers: 8 6
- 10G Ethernet numbers: 4 2
- SerDes lanes: 16 8
- Serial RapidIO,RMan: 2 no
- SATA Controller: 2 no
- Aurora: yes no
- SoC Package: 896-pins 780-pins
-
-
-T2080PCIe-RDB board Overview
-----------------------------
- - SERDES Configuration
- - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
- - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
- - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
- - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
- - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
- - SerDes-2 Lane G-H: to SATA1 & SATA2
- - Ethernet
- - Two on-board 10M/100M/1G RGMII ethernet ports
- - Two on-board 10Gbps XFI fiber ports
- - Two on-board 10Gbps Base-T copper ports
- - DDR Memory
- - Supports 72bit 4GB DDR3-LP SODIMM
- - PCIe
- - One PCIe x4 gold-finger
- - One PCIe x4 connector
- - One PCIe x2 end-point device (C293 Crypto co-processor)
- - IFC/Local Bus
- - NOR: 128MB 16-bit NOR Flash
- - NAND: 1GB 8-bit NAND flash
- - CPLD: for system controlling with programable header on-board
- - SATA
- - Two SATA 2.0 onnectors on-board
- - USB
- - Supports two USB 2.0 ports with integrated PHYs
- - Two type A ports with 5V@1.5A per port.
- - SDHC
- - one TF-card connector on-board
- - SPI
- - On-board 64MB SPI flash
- - Other
- - Two Serial ports
- - Four I2C ports
-
-
-System Memory map
------------------
-Start Address End Address Description Size
-0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB
-0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
-0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
-0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB
-0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
-0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
-0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
-0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
-0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
-0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
-0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
-0xC_4000_0000 0xC_4FFF_FFFF PCI Express 4 Mem Space 256MB
-0xC_3000_0000 0xC_3FFF_FFFF PCI Express 3 Mem Space 256MB
-0xC_2000_0000 0xC_2FFF_FFFF PCI Express 2 Mem Space 256MB
-0xC_0000_0000 0xC_1FFF_FFFF PCI Express 1 Mem Space 512MB
-0x0_0000_0000 0x0_ffff_ffff DDR 4GB
-
-
-128M NOR Flash memory Map
--------------------------
-Start Address End Address Definition Max size
-0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB
-0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB
-0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
-0xEFE00000 0xEFE3FFFF PHY CS4315 firmware 256KB
-0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
-0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
-0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
-0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
-0xEBF40000 0xEBFFFFFF U-Boot (alt bank) 768KB
-0xEBF20000 0xEBF3FFFF U-Boot env (alt bank) 128KB
-0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
-0xEBE00000 0xEBE3FFFF PHY CS4315 firmware (alt bank) 256KB
-0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
-0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
-0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
-0xE8000000 0xE801FFFF RCW (current bank) 128KB
-
-
-T2080PCIe-RDB Ethernet Port Map
--------------------------------
-Label In Uboot In Linux FMan Address Comments PHY
-ETH0 FM1@GTEC1 fm1-mac9 0xfe4f0000 10G SFP+ (CS4315)
-ETH1 FM1@GTEC2 fm1-mac10 0xfe4f2000 10G SFP+ (CS4315)
-ETH2 FM1@GTEC3 fm1-mac1 0xfe4e0000 10G Base-T (AQ1202)
-ETH3 FM1@GTEC4 fm1-mac2 0xfe4e2000 10G Base-T (AQ1202)
-ETH4 FM1@DTSEC3 fm1-mac3 0xfe4e4000 1G RGMII (RTL8211E)
-ETH5 FM1@DTSEC4 fm1-mac4 0xfe4e6000 1G RGMII (RTL8211E)
-
-
-T2080PCIe-RDB Default DIP-Switch setting
-----------------------------------------
-SW1[1:8] = '00010011'
-SW2[1:8] = '10111111'
-SW3[1:8] = '11100001'
-
-Software configurations and board settings
-------------------------------------------
-1. NOR boot:
- a. build NOR boot image
- $ make T2080RDB_config
- $ make
- b. program u-boot.bin image to NOR flash
- => tftp 1000000 u-boot.bin
- => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
- set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
-
- Switching between default bank and alternate bank on NOR flash
- To change boot source to vbank4:
- via software: run command 'cpld reset altbank' in U-Boot.
- via DIP-switch: set SW3[5:7] = '100'
-
- To change boot source to vbank0:
- via software: run command 'cpld reset' in U-Boot.
- via DIP-Switch: set SW3[5:7] = '000'
-
-2. NAND Boot:
- a. build PBL image for NAND boot
- $ make T2080RDB_NAND_config
- $ make
- b. program u-boot-with-spl-pbl.bin to NAND flash
- => tftp 1000000 u-boot-with-spl-pbl.bin
- => nand erase 0 d0000
- => nand write 1000000 0 $filesize
- set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot
-
-3. SPI Boot:
- a. build PBL image for SPI boot
- $ make T2080RDB_SPIFLASH_config
- $ make
- b. program u-boot-with-spl-pbl.bin to SPI flash
- => tftp 1000000 u-boot-with-spl-pbl.bin
- => sf probe 0
- => sf erase 0 d0000
- => sf write 1000000 0 $filesize
- set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
-
-4. SD Boot:
- a. build PBL image for SD boot
- $ make T2080RDB_SDCARD_config
- $ make
- b. program u-boot-with-spl-pbl.bin to micro-SD/TF card
- => tftp 1000000 u-boot-with-spl-pbl.bin
- => mmc write 1000000 8 0x800
- set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
-
-
-2-stage NAND/SPI/SD boot loader
--------------------------------
-PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
-SPL further initializes DDR using SPD and environment variables
-and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR.
-Finally SPL transers control to U-Boot for futher booting.
-
-SPL has following features:
- - Executes within 256K
- - No relocation required
-
-Run time view of SPL framework
--------------------------------------------------
-|Area | Address |
--------------------------------------------------
-|SecureBoot header | 0xFFFC0000 (32KB) |
--------------------------------------------------
-|GD, BD | 0xFFFC8000 (4KB) |
--------------------------------------------------
-|ENV | 0xFFFC9000 (8KB) |
--------------------------------------------------
-|HEAP | 0xFFFCB000 (50KB) |
--------------------------------------------------
-|STACK | 0xFFFD8000 (22KB) |
--------------------------------------------------
-|U-Boot SPL | 0xFFFD8000 (160KB) |
--------------------------------------------------
-
-NAND Flash memory Map on T2080RDB
---------------------------------------------------------------
-Start End Definition Size
-0x000000 0x0FFFFF U-Boot img 1MB (2 blocks)
-0x100000 0x17FFFF U-Boot env 512KB (1 block)
-0x180000 0x1FFFFF FMAN ucode 512KB (1 block)
-0x200000 0x27FFFF CS4315 ucode 512KB (1 block)
-
-
-Micro SD Card memory Map on T2080RDB
-----------------------------------------------------
-Block #blocks Definition Size
-0x008 2048 U-Boot img 1MB
-0x800 0016 U-Boot env 8KB
-0x820 0128 FMAN ucode 64KB
-0x8a0 0512 CS4315 ucode 256KB
-
-
-SPI Flash memory Map on T2080RDB
-----------------------------------------------------
-Start End Definition Size
-0x000000 0x0FFFFF U-Boot img 1MB
-0x100000 0x101FFF U-Boot env 8KB
-0x110000 0x11FFFF FMAN ucode 64KB
-0x120000 0x15FFFF CS4315 ucode 256KB
-
-
-How to update the ucode of Cortina CS4315/CS4340 10G PHY
---------------------------------------------------------
-=> tftp 1000000 CS4315-CS4340-PHY-ucode.txt
-=> pro off all;era 0xefe00000 0xefefffff;cp.b 1000000 0xefe00000 $filesize
-
-
-How to update the ucode of Freescale FMAN
------------------------------------------
-=> tftp 1000000 fsl_fman_ucode_t2080_r1.0.bin
-=> pro off all;erase 0xeff00000 0xeff1ffff;cp 1000000 0xeff00000 $filesize
-
-
-For more details, please refer to T2080PCIe-RDB User Guide and access
-website www.freescale.com and Freescale QorIQ SDK Infocenter document.
-
-Device tree support and how to enable it for different configs
---------------------------------------------------------------
-Device tree support is available for t2080rdb for below mentioned boot,
-1. NOR Boot
-2. NAND Boot
-3. SD Boot
-4. SPIFLASH Boot
-
-To enable device tree support for other boot, below configs need to be
-enabled in relative defconfig file,
-1. CONFIG_DEFAULT_DEVICE_TREE="t2080rdb" (Change default device tree name if required)
-2. CONFIG_OF_CONTROL
-3. CONFIG_MPC85XX_HAVE_RESET_VECTOR if reset vector is located at
- CONFIG_RESET_VECTOR_ADDRESS - 0xffc
-
-If device tree support is enabled in defconfig,
-1. use 'u-boot-with-dtb.bin' for NOR boot.
-2. use 'u-boot-with-spl-pbl.bin' for other boot.
deleted file mode 100644
@@ -1,70 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor
- *
- * Freescale T2080RDB board-specific CPLD controlling supports.
- */
-
-#include <common.h>
-#include <command.h>
-#include "cpld.h"
-
-u8 cpld_read(unsigned int reg)
-{
- void *p = (void *)CONFIG_SYS_CPLD_BASE;
-
- return in_8(p + reg);
-}
-
-void cpld_write(unsigned int reg, u8 value)
-{
- void *p = (void *)CONFIG_SYS_CPLD_BASE;
-
- out_8(p + reg, value);
-}
-
-/* Set the boot bank to the alternate bank */
-void cpld_set_altbank(void)
-{
- u8 reg = CPLD_READ(flash_csr);
-
- reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK;
- CPLD_WRITE(flash_csr, reg);
- CPLD_WRITE(reset_ctl, CPLD_LBMAP_RESET);
-}
-
-/* Set the boot bank to the default bank */
-void cpld_set_defbank(void)
-{
- u8 reg = CPLD_READ(flash_csr);
-
- reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK;
- CPLD_WRITE(flash_csr, reg);
- CPLD_WRITE(reset_ctl, CPLD_LBMAP_RESET);
-}
-
-int do_cpld(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
-{
- int rc = 0;
-
- if (argc <= 1)
- return cmd_usage(cmdtp);
-
- if (strcmp(argv[1], "reset") == 0) {
- if (strcmp(argv[2], "altbank") == 0)
- cpld_set_altbank();
- else
- cpld_set_defbank();
- } else {
- rc = cmd_usage(cmdtp);
- }
-
- return rc;
-}
-
-U_BOOT_CMD(
- cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
- "Reset the board or alternate bank",
- "reset: reset to default bank\n"
- "cpld reset altbank: reset to alternate bank\n"
-);
deleted file mode 100644
@@ -1,44 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014 Freescale Semiconductor
- */
-
-/*
- * CPLD register set of T2080RDB board-specific.
- */
-struct cpld_data {
- u8 chip_id1; /* 0x00 - Chip ID1 register */
- u8 chip_id2; /* 0x01 - Chip ID2 register */
- u8 hw_ver; /* 0x02 - Hardware Revision Register */
- u8 sw_ver; /* 0x03 - Software Revision register */
- u8 res0[12]; /* 0x04 - 0x0F - not used */
- u8 reset_ctl; /* 0x10 - Reset control Register */
- u8 flash_csr; /* 0x11 - Flash control and status register */
- u8 thermal_csr; /* 0x12 - Thermal control and status register */
- u8 led_csr; /* 0x13 - LED control and status register */
- u8 sfp_csr; /* 0x14 - SFP+ control and status register */
- u8 misc_csr; /* 0x15 - Misc control and status register */
- u8 boot_or; /* 0x16 - Boot config override register */
- u8 boot_cfg1; /* 0x17 - Boot configuration register 1 */
- u8 boot_cfg2; /* 0x18 - Boot configuration register 2 */
-} cpld_data_t;
-
-u8 cpld_read(unsigned int reg);
-void cpld_write(unsigned int reg, u8 value);
-
-#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
-#define CPLD_WRITE(reg, value) \
- cpld_write(offsetof(struct cpld_data, reg), value)
-
-/* CPLD on IFC */
-#define CPLD_LBMAP_MASK 0x3F
-#define CPLD_BANK_SEL_MASK 0x07
-#define CPLD_BANK_OVERRIDE 0x40
-#define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */
-#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK 0 */
-#define CPLD_LBMAP_RESET 0xFF
-#define CPLD_LBMAP_SHIFT 0x03
-#define CPLD_BOOT_SEL 0x80
-
-/* RSTCON Register */
-#define CPLD_RSTCON_EDC_RST 0x04
deleted file mode 100644
@@ -1,118 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <hwconfig.h>
-#include <init.h>
-#include <log.h>
-#include <asm/mmu.h>
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-#include <asm/fsl_law.h>
-#include "ddr.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
- ulong ddr_freq;
-
- if (ctrl_num > 1) {
- printf("Not supported controller number %d\n", ctrl_num);
- return;
- }
- if (!pdimm->n_ranks)
- return;
-
- pbsp = udimms[0];
-
- /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
- * freqency and n_banks specified in board_specific_parameters table.
- */
- ddr_freq = get_ddr_freq(0) / 1000000;
- while (pbsp->datarate_mhz_high) {
- if (pbsp->n_ranks == pdimm->n_ranks &&
- (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
- if (ddr_freq <= pbsp->datarate_mhz_high) {
- popts->clk_adjust = pbsp->clk_adjust;
- popts->wrlvl_start = pbsp->wrlvl_start;
- popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
- popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
- goto found;
- }
- pbsp_highest = pbsp;
- }
- pbsp++;
- }
-
- if (pbsp_highest) {
- printf("Error: board specific timing not found");
- printf("for data rate %lu MT/s\n", ddr_freq);
- printf("Trying to use the highest speed (%u) parameters\n",
- pbsp_highest->datarate_mhz_high);
- popts->clk_adjust = pbsp_highest->clk_adjust;
- popts->wrlvl_start = pbsp_highest->wrlvl_start;
- popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
- popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
- } else {
- panic("DIMM is not supported by this board");
- }
-found:
- debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
- "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
- "wrlvl_ctrl_3 0x%x\n",
- pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
- pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
- pbsp->wrlvl_ctl_3);
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 0;
- /*
- * Write leveling override
- */
- popts->wrlvl_override = 1;
- popts->wrlvl_sample = 0xf;
-
- /*
- * Rtt and Rtt_WR override
- */
- popts->rtt_override = 0;
-
- /* Enable ZQ calibration */
- popts->zq_en = 1;
-
- /* DHC_EN =1, ODT = 75 Ohm */
- popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
- popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
-
- /* optimize cpo for erratum A-009942 */
- popts->cpo_sample = 0x54;
-}
-
-int dram_init(void)
-{
- phys_size_t dram_size;
-
-#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
- puts("Initializing....using SPD\n");
- dram_size = fsl_ddr_sdram();
-#else
- /* DDR has been initialised by first stage boot loader */
- dram_size = fsl_ddr_sdram_size();
-#endif
- dram_size = setup_ddr_tlbs(dram_size / 0x100000);
- dram_size *= 0x100000;
-
- gd->ram_size = dram_size;
-
- return 0;
-}
deleted file mode 100644
@@ -1,46 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#ifndef __DDR_H__
-#define __DDR_H__
-struct board_specific_parameters {
- u32 n_ranks;
- u32 datarate_mhz_high;
- u32 rank_gb;
- u32 clk_adjust;
- u32 wrlvl_start;
- u32 wrlvl_ctl_2;
- u32 wrlvl_ctl_3;
-};
-
-/*
- * These tables contain all valid speeds we want to override with board
- * specific parameters. datarate_mhz_high values need to be in ascending order
- * for each n_ranks group.
- */
-
-static const struct board_specific_parameters udimm0[] = {
- /*
- * memory controller 0
- * num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
- * ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
- */
- {2, 1200, 2, 10, 7, 0x0808090a, 0x0b0c0c0a},
- {2, 1500, 2, 10, 6, 0x07070809, 0x0a0b0b09},
- {2, 1600, 2, 10, 8, 0x0808070b, 0x0c0d0e0a},
- {2, 1700, 2, 8, 7, 0x080a0a0c, 0x0c0d0e0a},
- {2, 1900, 0, 10, 7, 0x0808080c, 0x0b0c0c09},
- {1, 1200, 2, 10, 7, 0x0808090a, 0x0b0c0c0a},
- {1, 1500, 2, 10, 6, 0x07070809, 0x0a0b0b09},
- {1, 1600, 2, 10, 8, 0x0808070b, 0x0c0d0e0a},
- {1, 1700, 2, 8, 7, 0x080a0a0c, 0x0c0d0e0a},
- {1, 1900, 0, 10, 7, 0x0808080c, 0x0b0c0c09},
- {}
-};
-
-static const struct board_specific_parameters *udimms[] = {
- udimm0,
-};
-#endif
deleted file mode 100644
@@ -1,107 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- *
- * Shengzhou Liu <Shengzhou.Liu@freescale.com>
- */
-
-#include <common.h>
-#include <command.h>
-#include <fdt_support.h>
-#include <net.h>
-#include <netdev.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_law.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_portals.h>
-#include <asm/fsl_liodn.h>
-#include <malloc.h>
-#include <fm_eth.h>
-#include <fsl_mdio.h>
-#include <miiphy.h>
-#include <phy.h>
-#include <fsl_dtsec.h>
-#include <asm/fsl_serdes.h>
-
-int board_eth_init(bd_t *bis)
-{
-#if defined(CONFIG_FMAN_ENET)
- int i, interface;
- struct memac_mdio_info dtsec_mdio_info;
- struct memac_mdio_info tgec_mdio_info;
- struct mii_dev *dev;
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_s1;
-
- srds_s1 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
- srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
-
- dtsec_mdio_info.regs =
- (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
-
- dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
-
- /* Register the 1G MDIO bus */
- fm_memac_mdio_init(bis, &dtsec_mdio_info);
-
- tgec_mdio_info.regs =
- (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
- tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
-
- /* Register the 10G MDIO bus */
- fm_memac_mdio_init(bis, &tgec_mdio_info);
-
- /* Set the two on-board RGMII PHY address */
- fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
- fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR);
-
- switch (srds_s1) {
- case 0x66:
- case 0x6b:
- fm_info_set_phy_address(FM1_10GEC1, CORTINA_PHY_ADDR1);
- fm_info_set_phy_address(FM1_10GEC2, CORTINA_PHY_ADDR2);
- fm_info_set_phy_address(FM1_10GEC3, FM1_10GEC3_PHY_ADDR);
- fm_info_set_phy_address(FM1_10GEC4, FM1_10GEC4_PHY_ADDR);
- break;
- default:
- printf("SerDes1 protocol 0x%x is not supported on T208xRDB\n",
- srds_s1);
- break;
- }
-
- for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
- interface = fm_info_get_enet_if(i);
- switch (interface) {
- case PHY_INTERFACE_MODE_RGMII:
- dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
- fm_info_set_mdio(i, dev);
- break;
- default:
- break;
- }
- }
-
- for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
- switch (fm_info_get_enet_if(i)) {
- case PHY_INTERFACE_MODE_XGMII:
- dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
- fm_info_set_mdio(i, dev);
- break;
- default:
- break;
- }
- }
-
- cpu_eth_init(bis);
-#endif /* CONFIG_FMAN_ENET */
-
- return pci_eth_init(bis);
-}
-
-void fdt_fixup_board_enet(void *fdt)
-{
- return;
-}
deleted file mode 100644
@@ -1,33 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008-2014 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
- SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
- SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
- SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
-#endif
-#ifdef CONFIG_SYS_CPLD_BASE_PHYS
- SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
- /* Limit DCSR to 32M to access NPC Trace Buffer */
- SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE_PHYS
- SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
-#endif
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
deleted file mode 100644
@@ -1,25 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2007-2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <pci.h>
-#include <asm/fsl_pci.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <asm/fsl_serdes.h>
-
-#if !defined(CONFIG_DM_PCI)
-void pci_init_board(void)
-{
- fsl_pcie_init_board(0);
-}
-
-void pci_of_setup(void *blob, bd_t *bd)
-{
- FT_FSL_PCI_SETUP;
-}
-#endif
deleted file mode 100644
@@ -1,112 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/* Copyright 2013 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <clock_legacy.h>
-#include <console.h>
-#include <env_internal.h>
-#include <init.h>
-#include <malloc.h>
-#include <ns16550.h>
-#include <nand.h>
-#include <i2c.h>
-#include <mmc.h>
-#include <fsl_esdhc.h>
-#include <spi_flash.h>
-#include "../common/spl.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-phys_size_t get_effective_memsize(void)
-{
- return CONFIG_SYS_L3_SIZE;
-}
-
-unsigned long get_board_sys_clk(void)
-{
- return CONFIG_SYS_CLK_FREQ;
-}
-
-unsigned long get_board_ddr_clk(void)
-{
- return CONFIG_DDR_CLK_FREQ;
-}
-
-void board_init_f(ulong bootflag)
-{
- u32 plat_ratio, sys_clk, ccb_clk;
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-
- /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
- memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
-
- /* Update GD pointer */
- gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
-
- console_init_f();
-
- /* initialize selected port with appropriate baud rate */
- sys_clk = get_board_sys_clk();
- plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
- ccb_clk = sys_clk * plat_ratio / 2;
-
- NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
- ccb_clk / 16 / CONFIG_BAUDRATE);
-
-#if defined(CONFIG_SPL_MMC_BOOT)
- puts("\nSD boot...\n");
-#elif defined(CONFIG_SPL_SPI_BOOT)
- puts("\nSPI boot...\n");
-#elif defined(CONFIG_SPL_NAND_BOOT)
- puts("\nNAND boot...\n");
-#endif
-
- relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
-}
-
-void board_init_r(gd_t *gd, ulong dest_addr)
-{
- bd_t *bd;
-
- bd = (bd_t *)(gd + sizeof(gd_t));
- memset(bd, 0, sizeof(bd_t));
- gd->bd = bd;
- bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
- bd->bi_memsize = CONFIG_SYS_L3_SIZE;
-
- arch_cpu_init();
- get_clocks();
- mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
- CONFIG_SPL_RELOC_MALLOC_SIZE);
- gd->flags |= GD_FLG_FULL_MALLOC_INIT;
-
-#ifdef CONFIG_SPL_NAND_BOOT
- nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)SPL_ENV_ADDR);
-#endif
-#ifdef CONFIG_SPL_MMC_BOOT
- mmc_initialize(bd);
- mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)SPL_ENV_ADDR);
-#endif
-#ifdef CONFIG_SPL_SPI_BOOT
- fsl_spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)SPL_ENV_ADDR);
-#endif
-
- gd->env_addr = (ulong)(SPL_ENV_ADDR);
- gd->env_valid = ENV_VALID;
-
- i2c_init_all();
-
- dram_init();
-
-#ifdef CONFIG_SPL_MMC_BOOT
- mmc_boot();
-#elif defined(CONFIG_SPL_SPI_BOOT)
- fsl_spi_boot();
-#elif defined(CONFIG_SPL_NAND_BOOT)
- nand_boot();
-#endif
-}
deleted file mode 100644
@@ -1,19 +0,0 @@
-#PBL preamble and RCW header
-aa55aa55 010e0100
-
-#For T2080 v1.0
-#SerDes=0x66_0x16, Core=1533MHz, DDR=1600MT/s
-#120c0017 15000000 00000000 00000000
-#66150002 00008400 ec104000 c1000000
-#00000000 00000000 00000000 000307fc
-#00000000 00000000 00000000 00000004
-
-#For T2080 v1.1
-#SerDes=0x66_0x15, Core:1800MHz, DDR:1600MT/s
-#1206001b 15000000 00000000 00000000
-
-#SerDes=0x66_0x15, Core:1800MHz, DDR:1867MT/s
-1207001b 15000000 00000000 00000000
-66150002 00000000 e8104000 c1000000
-00800000 00000000 00000000 000307fc
-00000000 00000000 00000000 00000004
deleted file mode 100644
@@ -1,40 +0,0 @@
-#
-# Copyright 2013 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Refer doc/README.pblimage for more details about how-to configure
-# and create PBL boot image
-#
-
-#PBI commands
-#Initialize CPC1
-09010000 00200400
-09138000 00000000
-091380c0 00000100
-#512KB SRAM
-09010100 00000000
-09010104 fff80009
-09010f00 08000000
-#enable CPC1
-09010000 80000000
-#Configure LAW for CPC1
-09000d00 00000000
-09000d04 fff80000
-09000d08 81000012
-#Initialize eSPI controller, default configuration is slow for eSPI to
-#load data, this configuration comes from u-boot eSPI driver.
-09110000 80000403
-09110020 2d170008
-09110024 00100008
-09110028 00100008
-0911002c 00100008
-#Errata for slowing down the MDC clock to make it <= 2.5 MHZ
-094fc030 00008148
-094fd030 00008148
-#Configure alternate space
-09000010 00000000
-09000014 ff000000
-09000018 81000000
-#Flush PBL data
-091380c0 00100000
deleted file mode 100644
@@ -1,19 +0,0 @@
-#PBL preamble and RCW header
-aa55aa55 010e0100
-
-#For T2080 v1.0
-#SerDes=0x66_0x16, Core=1533MHz, DDR=1600MT/s
-#120c0017 15000000 00000000 00000000
-#66150002 00008400 ec104000 c1000000
-#00000000 00000000 00000000 000307fc
-#00000000 00000000 00000000 00000004
-
-#For T2080 v1.1
-#SerDes=0x66_0x15, Core:1800MHz, DDR:1600MT/s
-#1206001b 15000000 00000000 00000000
-
-#SerDes=0x66_0x15, Core:1800MHz, DDR:1867MT/s
-1207001b 15000000 00000000 00000000
-66150002 00000000 68104000 c1000000
-00800000 00000000 00000000 000307fc
-00000000 00000000 00000000 00000004
deleted file mode 100644
@@ -1,19 +0,0 @@
-#PBL preamble and RCW header
-aa55aa55 010e0100
-
-#For T2080 v1.0
-#SerDes=0x66_0x16, Core=1533MHz, DDR=1600MT/s
-#120c0017 15000000 00000000 00000000
-#66150002 00008400 ec104000 c1000000
-#00000000 00000000 00000000 000307fc
-#00000000 00000000 00000000 00000004
-
-#For T2080 v1.1
-#SerDes=0x66_0x15, Core:1800MHz, DDR:1600MT/s
-#1206001b 15000000 00000000 00000000
-
-#SerDes=0x66_0x15, Core:1800MHz, DDR:1867MT/s
-1207001b 15000000 00000000 00000000
-66150002 00000000 58104000 c1000000
-00800000 00000000 00000000 000307fc
-00000000 00000000 00000000 00000004
deleted file mode 100644
@@ -1,142 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2009-2013 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <fdt_support.h>
-#include <i2c.h>
-#include <image.h>
-#include <init.h>
-#include <netdev.h>
-#include <linux/compiler.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_law.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_liodn.h>
-#include <fm_eth.h>
-#include "t208xrdb.h"
-#include "cpld.h"
-#include "../common/vid.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int checkboard(void)
-{
- struct cpu_type *cpu = gd->arch.cpu;
- static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"};
-
- printf("Board: %sRDB, ", cpu->name);
- printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ",
- CPLD_READ(hw_ver), CPLD_READ(sw_ver));
-
-#ifdef CONFIG_SDCARD
- puts("SD/MMC\n");
-#elif CONFIG_SPIFLASH
- puts("SPI\n");
-#else
- u8 reg;
-
- reg = CPLD_READ(flash_csr);
-
- if (reg & CPLD_BOOT_SEL) {
- puts("NAND\n");
- } else {
- reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
- printf("NOR vBank%d\n", reg);
- }
-#endif
-
- puts("SERDES Reference Clocks:\n");
- printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
- printf("SD2_CLK1=%s, SD2_CLK2=%s\n", freq[0], freq[0]);
-
- return 0;
-}
-
-int board_early_init_r(void)
-{
- const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
- int flash_esel = find_tlb_idx((void *)flashbase, 1);
- /*
- * Remap Boot flash + PROMJET region to caching-inhibited
- * so that flash can be erased properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
- if (flash_esel == -1) {
- /* very unlikely unless something is messed up */
- puts("Error: Could not find TLB for FLASH BASE\n");
- flash_esel = 2; /* give our best effort to continue */
- } else {
- /* invalidate existing TLB entry for flash + promjet */
- disable_tlb(flash_esel);
- }
-
- set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, flash_esel, BOOKE_PAGESZ_256M, 1);
-
- /*
- * Adjust core voltage according to voltage ID
- * This function changes I2C mux to channel 2.
- */
- if (adjust_vdd(0))
- printf("Warning: Adjusting core voltage failed.\n");
- return 0;
-}
-
-unsigned long get_board_sys_clk(void)
-{
- return CONFIG_SYS_CLK_FREQ;
-}
-
-unsigned long get_board_ddr_clk(void)
-{
- return CONFIG_DDR_CLK_FREQ;
-}
-
-int misc_init_r(void)
-{
- u8 reg;
-
- /* Reset CS4315 PHY */
- reg = CPLD_READ(reset_ctl);
- reg |= CPLD_RSTCON_EDC_RST;
- CPLD_WRITE(reset_ctl, reg);
-
- return 0;
-}
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = env_get_bootm_low();
- size = env_get_bootm_size();
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#ifdef CONFIG_PCI
- pci_of_setup(blob, bd);
-#endif
-
- fdt_fixup_liodn(blob);
- fsl_fdt_fixup_dr_usb(blob, bd);
-
-#ifdef CONFIG_SYS_DPAA_FMAN
- fdt_fixup_fman_ethernet(blob);
- fdt_fixup_board_enet(blob);
-#endif
-
- return 0;
-}
deleted file mode 100644
@@ -1,12 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#ifndef __CORENET_DS_H__
-#define __CORENET_DS_H__
-
-void fdt_fixup_board_enet(void *blob);
-void pci_of_setup(void *blob, bd_t *bd);
-
-#endif
deleted file mode 100644
@@ -1,152 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008-2014 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 */
- /* *I*** - Covers boot page */
-#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
- /*
- * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
- * SRAM is at 0xfff00000, it covered the 0xfffff000.
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_1M, 1),
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
- /*
- * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the
- * space is at 0xfff00000, it covered the 0xfffff000.
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR,
- CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
- 0, 0, BOOKE_PAGESZ_1M, 1),
-#else
- SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_4K, 1),
-#endif
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_16M, 1),
-
- /* *I*G* - Flash, localbus */
- /* This will be changed to *I*G* after relocation to RAM. */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
- 0, 2, BOOKE_PAGESZ_256M, 1),
-
-#ifndef CONFIG_SPL_BUILD
- /* *I*G* - PCIe 1, 0x80000000 */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_512M, 1),
-
- /* *I*G* - PCIe 2, 0xa0000000 */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_256M, 1),
-
- /* *I*G* - PCIe 3, 0xb0000000 */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_256M, 1),
-
-
- /* *I*G* - PCIe 4, 0xc0000000 */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE4_MEM_VIRT, CONFIG_SYS_PCIE4_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_256M, 1),
-
- /* *I*G* - PCI I/O */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 7, BOOKE_PAGESZ_256K, 1),
-
- /* Bman/Qman */
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 9, BOOKE_PAGESZ_16M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
- CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 10, BOOKE_PAGESZ_16M, 1),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 11, BOOKE_PAGESZ_16M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
- CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 12, BOOKE_PAGESZ_16M, 1),
-#endif
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 13, BOOKE_PAGESZ_32M, 1),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE
- /*
- * *I*G - NAND
- * entry 14 and 15 has been used hard coded, they will be disabled
- * in cpu_init_f, so we use entry 16 for nand.
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 16, BOOKE_PAGESZ_64K, 1),
-#endif
-#ifdef CONFIG_SYS_CPLD_BASE
- SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 17, BOOKE_PAGESZ_4K, 1),
-#endif
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
- /*
- * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for
- * fetching ucode and ENV from master
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR,
- CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
- 0, 18, BOOKE_PAGESZ_1M, 1),
-#endif
-#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 19, BOOKE_PAGESZ_2G, 1)
-#endif
-
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
deleted file mode 100644
@@ -1,84 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x00201000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T2080RDB=y
-CONFIG_SYS_CUSTOM_LDSCRIPT=y
-CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL"
-CONFIG_BOOTDELAY=10
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_NAND_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)"
-# CONFIG_CMD_IRQ is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="t2080rdb"
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_DM=y
-CONFIG_FSL_CAAM=y
-CONFIG_DM_I2C=y
-CONFIG_DM_MMC=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_CORTINA=y
-CONFIG_SYS_CORTINA_FW_IN_NAND=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_DM_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_FSL=y
-CONFIG_SYS_QE_FMAN_FW_IN_NAND=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_DM_USB=y
deleted file mode 100644
@@ -1,81 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x00201000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T2080RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SDCARD"
-CONFIG_BOOTDELAY=10
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_MMC_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)"
-# CONFIG_CMD_IRQ is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="t2080rdb"
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_DM=y
-CONFIG_FSL_CAAM=y
-CONFIG_DM_I2C=y
-CONFIG_DM_MMC=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_CORTINA=y
-CONFIG_SYS_CORTINA_FW_IN_MMC=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_DM_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_FSL=y
-CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_DM_USB=y
deleted file mode 100644
@@ -1,63 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_NXP_ESBC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T2080RDB=y
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)"
-# CONFIG_CMD_IRQ is not set
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_CORTINA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_RSA=y
-CONFIG_SPL_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,84 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x00201000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T2080RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPIFLASH"
-CONFIG_BOOTDELAY=10
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_SPI_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)"
-# CONFIG_CMD_IRQ is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="t2080rdb"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_ENV_ADDR=0xFFFC9000
-CONFIG_DM=y
-CONFIG_FSL_CAAM=y
-CONFIG_DM_I2C=y
-CONFIG_DM_MMC=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_CORTINA=y
-CONFIG_SYS_CORTINA_FW_IN_SPIFLASH=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_DM_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_FSL=y
-CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_DM_USB=y
deleted file mode 100644
@@ -1,53 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T2080RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="SRIO_PCIE_BOOT_SLAVE"
-CONFIG_BOOTDELAY=10
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-# CONFIG_CMD_IRQ is not set
-CONFIG_ENV_IS_IN_REMOTE=y
-CONFIG_ENV_ADDR=0xFFE20000
-CONFIG_FSL_CAAM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_CORTINA=y
-CONFIG_SYS_CORTINA_FW_IN_REMOTE=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_REMOTE=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,68 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T2080RDB=y
-CONFIG_MPC85XX_HAVE_RESET_VECTOR=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:1m(uboot),5m(kernel),128k(dtb),-(user)"
-# CONFIG_CMD_IRQ is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="t2080rdb"
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xEFF20000
-CONFIG_DM=y
-CONFIG_FSL_CAAM=y
-CONFIG_DM_I2C=y
-CONFIG_DM_MMC=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_CORTINA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_DM_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_FSL=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_DM_USB=y
deleted file mode 100644
@@ -1,717 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- * Copyright 2020 NXP
- */
-
-/*
- * T2080 RDB/PCIe board configuration file
- */
-
-#ifndef __T2080RDB_H
-#define __T2080RDB_H
-
-#include <linux/stringify.h>
-
-#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
-#define CONFIG_FSL_SATA_V2
-
-/* High Level Configuration Options */
-#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-#endif
-
-#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
-#define CONFIG_ENV_OVERWRITE
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
-
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_PAD_TO 0x40000
-#define CONFIG_SPL_MAX_SIZE 0x28000
-#define RESET_VECTOR_OFFSET 0x27FFC
-#define BOOT_PAGE_OFFSET 0x27000
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_SKIP_RELOCATE
-#define CONFIG_SPL_COMMON_INIT_DDR
-#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
-#endif
-
-#ifdef CONFIG_MTD_RAW_NAND
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
-#endif
-
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
-#define CONFIG_SPL_SPI_FLASH_MINIMAL
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#endif
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
-#endif
-
-#ifdef CONFIG_SDCARD
-#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
-#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000)
-#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000)
-#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#endif
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
-#endif
-
-#endif /* CONFIG_RAMBOOT_PBL */
-
-#define CONFIG_SRIO_PCIE_BOOT_MASTER
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
-/* Set 1M boot space */
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
- (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
-#endif
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_DDR_ECC
-#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#endif
-
-#if defined(CONFIG_SPIFLASH)
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#endif
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ 66660000
-#define CONFIG_DDR_CLK_FREQ 133330000
-
-/*
- * Config the L3 Cache as L3 SRAM
- */
-#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
-#define CONFIG_SYS_L3_SIZE (512 << 10)
-#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
-#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10)
-#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
-
-#define CONFIG_SYS_DCSRBAR 0xf0000000
-#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
-
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/*
- * DDR Setup
- */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
-#define SPD_EEPROM_ADDRESS1 0x51
-#define SPD_EEPROM_ADDRESS2 0x52
-#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
-#define CTRL_INTLV_PREFERED cacheline
-
-/*
- * IFC Definitions
- */
-#define CONFIG_SYS_FLASH_BASE 0xe8000000
-#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
-#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
-
-/* NOR Flash Timing Params */
-#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
-
-#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
- FTIM0_NOR_TEADC(0x5) | \
- FTIM0_NOR_TEAHC(0x5))
-#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
- FTIM1_NOR_TRAD_NOR(0x1A) |\
- FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
- FTIM2_NOR_TCH(0x4) | \
- FTIM2_NOR_TWPH(0x0E) | \
- FTIM2_NOR_TWP(0x1c))
-#define CONFIG_SYS_NOR_FTIM3 0x0
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS }
-
-/* CPLD on IFC */
-#define CONFIG_SYS_CPLD_BASE 0xffdf0000
-#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
-#define CONFIG_SYS_CSPR2_EXT (0xf)
-#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
- | CSPR_PORT_SIZE_8 \
- | CSPR_MSEL_GPCM \
- | CSPR_V)
-#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
-#define CONFIG_SYS_CSOR2 0x0
-
-/* CPLD Timing parameters for IFC CS2 */
-#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
- FTIM0_GPCM_TEADC(0x0e) | \
- FTIM0_GPCM_TEAHC(0x0e))
-#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
- FTIM1_GPCM_TRAD(0x1f))
-#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
- FTIM2_GPCM_TCH(0x8) | \
- FTIM2_GPCM_TWP(0x1f))
-#define CONFIG_SYS_CS2_FTIM3 0x0
-
-/* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_BASE 0xff800000
-#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
-
-#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
- | CSPR_MSEL_NAND /* MSEL = NAND */ \
- | CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
- | CSOR_NAND_PGS_2K /* Page Size = 2K */\
- | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
- FTIM0_NAND_TWP(0x18) | \
- FTIM0_NAND_TWCHT(0x07) | \
- FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
- FTIM1_NAND_TWBE(0x39) | \
- FTIM1_NAND_TRR(0x0e) | \
- FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
- FTIM2_NAND_TREH(0x0a) | \
- FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3 0x0
-
-#define CONFIG_SYS_NAND_DDR_LAW 11
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
-
-#if defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
-#else
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
-#endif
-
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
-#define CONFIG_HWCONFIG
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
- ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
- CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
-#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
-
-/*
- * I2C
- */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
-#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
-#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
-#define CONFIG_SYS_FSL_I2C_SPEED 100000
-#define CONFIG_SYS_FSL_I2C2_SPEED 100000
-#define CONFIG_SYS_FSL_I2C3_SPEED 100000
-#define CONFIG_SYS_FSL_I2C4_SPEED 100000
-#else
-#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
-#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
-#endif
-
-#define CONFIG_SYS_I2C_FSL
-
-#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
-#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
-#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */
-#define I2C_MUX_CH_DEFAULT 0x8
-
-#define I2C_MUX_CH_VOL_MONITOR 0xa
-
-#define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv"
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_VID
-#endif
-#define CONFIG_VOL_MONITOR_IR36021_SET
-#define CONFIG_VOL_MONITOR_IR36021_READ
-/* The lowest and highest voltage allowed for T208xRDB */
-#define VDD_MV_MIN 819
-#define VDD_MV_MAX 1212
-
-/*
- * RapidIO
- */
-#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
-#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
-#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
-#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
-/*
- * for slave u-boot IMAGE instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
-/*
- * for slave UCODE and ENV instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
-
-/* slave core release by master*/
-#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
-#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
-
-/*
- * SRIO_PCIE_BOOT - SLAVE
- */
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
- (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
-#endif
-
-/*
- * eSPI - Enhanced SPI
- */
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-#define CONFIG_PCIE1 /* PCIE controller 1 */
-#define CONFIG_PCIE2 /* PCIE controller 2 */
-#define CONFIG_PCIE3 /* PCIE controller 3 */
-#define CONFIG_PCIE4 /* PCIE controller 4 */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-/* controller 1, direct to uli, tgtid 3, Base address 20000 */
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
-
-/* controller 2, Slot 2, tgtid 2, Base address 201000 */
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
-
-/* controller 3, Slot 1, tgtid 1, Base address 202000 */
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
-
-/* controller 4, Base address 203000 */
-#define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000
-#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull
-#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
-
-#ifdef CONFIG_PCI
-#if !defined(CONFIG_DM_PCI)
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#endif
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#endif
-
-/* Qman/Bman */
-#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_BMAN_NUM_PORTALS 18
-#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
-#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
-#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
-#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
-#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
-#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
- CONFIG_SYS_BMAN_CENA_SIZE)
-#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
-#define CONFIG_SYS_QMAN_NUM_PORTALS 18
-#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
-#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
-#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
-#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
-#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
-#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
- CONFIG_SYS_QMAN_CENA_SIZE)
-#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
-
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_SYS_DPAA_PME
-#define CONFIG_SYS_PMAN
-#define CONFIG_SYS_DPAA_DCE
-#define CONFIG_SYS_DPAA_RMAN /* RMan */
-#define CONFIG_SYS_INTERLAKEN
-
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
-#define CONFIG_CORTINA_FW_ADDR 0x120000
-
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 1MB (2048 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
-#define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0)
-
-#elif defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-/*
- * Slave has no ucode locally, it can fetch this from remote. When implementing
- * in two corenet boards, slave's ucode could be stored in master's memory
- * space, the address can be mapped from slave TLB->slave LAW->
- * slave SRIO or PCIE outbound window->master inbound window->
- * master LAW->the ucode address in master's memory space.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
-#define CONFIG_CORTINA_FW_ADDR 0xFFE10000
-#else
-#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
-#define CONFIG_CORTINA_FW_ADDR 0xEFE00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-#endif /* CONFIG_NOBQFMAN */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_CORTINA_FW_LENGTH 0x40000
-#define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */
-#define RGMII_PHY2_ADDR 0x02
-#define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */
-#define CORTINA_PHY_ADDR2 0x0d
-#define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */
-#define FM1_10GEC4_PHY_ADDR 0x01
-#endif
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME "FM1@DTSEC3"
-#endif
-
-/*
- * SATA
- */
-#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
-#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
-#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
-#define CONFIG_LBA48
-#endif
-
-/*
- * USB
- */
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_HAS_FSL_DR_USB
-#endif
-
-/*
- * SDHC
- */
-#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
-#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#endif
-
-/*
- * Dynamic MTD Partition support with mtdparts
- */
-
-/*
- * Environment
- */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-#define __USB_PHY_TYPE utmi
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:" \
- "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
- "bank_intlv=auto;" \
- "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
- "netdev=eth0\0" \
- "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
- "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot && " \
- "protect off $ubootaddr +$filesize && " \
- "erase $ubootaddr +$filesize && " \
- "cp.b $loadaddr $ubootaddr $filesize && " \
- "protect on $ubootaddr +$filesize && " \
- "cmp.b $loadaddr $ubootaddr $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=t2080rdb/ramdisk.uboot\0" \
- "fdtaddr=1e00000\0" \
- "fdtfile=t2080rdb/t2080rdb.dtb\0" \
- "bdev=sda3\0"
-
-/*
- * For emulation this causes u-boot to jump to the start of the
- * proof point app code automatically
- */
-#define CONFIG_PROOF_POINTS \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "cpu 1 release 0x29000000 - - -;" \
- "cpu 2 release 0x29000000 - - -;" \
- "cpu 3 release 0x29000000 - - -;" \
- "cpu 4 release 0x29000000 - - -;" \
- "cpu 5 release 0x29000000 - - -;" \
- "cpu 6 release 0x29000000 - - -;" \
- "cpu 7 release 0x29000000 - - -;" \
- "go 0x29000000"
-
-#define CONFIG_HVBOOT \
- "setenv bootargs config-addr=0x60000000; " \
- "bootm 0x01000000 - 0x00f00000"
-
-#define CONFIG_ALU \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "cpu 1 release 0x01000000 - - -;" \
- "cpu 2 release 0x01000000 - - -;" \
- "cpu 3 release 0x01000000 - - -;" \
- "cpu 4 release 0x01000000 - - -;" \
- "cpu 5 release 0x01000000 - - -;" \
- "cpu 6 release 0x01000000 - - -;" \
- "cpu 7 release 0x01000000 - - -;" \
- "go 0x01000000"
-
-#define CONFIG_LINUX \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "setenv ramdiskaddr 0x02000000;" \
- "setenv fdtaddr 0x00c00000;" \
- "setenv loadaddr 0x1000000;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_HDBOOT \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_LINUX
-
-#include <asm/fsl_secure_boot.h>
-
-#endif /* __T2080RDB_H */
This board has not been converted to CONFIG_DM_SPI by the deadline. Remove it. Patch-cc: Shengzhou Liu <Shengzhou.Liu@nxp.com> Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- arch/powerpc/cpu/mpc85xx/Kconfig | 1 - board/freescale/t208xrdb/Kconfig | 14 - board/freescale/t208xrdb/MAINTAINERS | 15 - board/freescale/t208xrdb/Makefile | 16 - board/freescale/t208xrdb/README | 283 -------- board/freescale/t208xrdb/cpld.c | 70 -- board/freescale/t208xrdb/cpld.h | 44 -- board/freescale/t208xrdb/ddr.c | 118 ---- board/freescale/t208xrdb/ddr.h | 46 -- board/freescale/t208xrdb/eth_t208xrdb.c | 107 --- board/freescale/t208xrdb/law.c | 33 - board/freescale/t208xrdb/pci.c | 25 - board/freescale/t208xrdb/spl.c | 112 --- board/freescale/t208xrdb/t2080_nand_rcw.cfg | 19 - board/freescale/t208xrdb/t2080_pbi.cfg | 40 -- board/freescale/t208xrdb/t2080_sd_rcw.cfg | 19 - board/freescale/t208xrdb/t2080_spi_rcw.cfg | 19 - board/freescale/t208xrdb/t208xrdb.c | 142 ---- board/freescale/t208xrdb/t208xrdb.h | 12 - board/freescale/t208xrdb/tlb.c | 152 ----- configs/T2080RDB_NAND_defconfig | 84 --- configs/T2080RDB_SDCARD_defconfig | 81 --- configs/T2080RDB_SECURE_BOOT_defconfig | 63 -- configs/T2080RDB_SPIFLASH_defconfig | 84 --- configs/T2080RDB_SRIO_PCIE_BOOT_defconfig | 53 -- configs/T2080RDB_defconfig | 68 -- include/configs/T208xRDB.h | 717 -------------------- 27 files changed, 2437 deletions(-) delete mode 100644 board/freescale/t208xrdb/Kconfig delete mode 100644 board/freescale/t208xrdb/MAINTAINERS delete mode 100644 board/freescale/t208xrdb/Makefile delete mode 100644 board/freescale/t208xrdb/README delete mode 100644 board/freescale/t208xrdb/cpld.c delete mode 100644 board/freescale/t208xrdb/cpld.h delete mode 100644 board/freescale/t208xrdb/ddr.c delete mode 100644 board/freescale/t208xrdb/ddr.h delete mode 100644 board/freescale/t208xrdb/eth_t208xrdb.c delete mode 100644 board/freescale/t208xrdb/law.c delete mode 100644 board/freescale/t208xrdb/pci.c delete mode 100644 board/freescale/t208xrdb/spl.c delete mode 100644 board/freescale/t208xrdb/t2080_nand_rcw.cfg delete mode 100644 board/freescale/t208xrdb/t2080_pbi.cfg delete mode 100644 board/freescale/t208xrdb/t2080_sd_rcw.cfg delete mode 100644 board/freescale/t208xrdb/t2080_spi_rcw.cfg delete mode 100644 board/freescale/t208xrdb/t208xrdb.c delete mode 100644 board/freescale/t208xrdb/t208xrdb.h delete mode 100644 board/freescale/t208xrdb/tlb.c delete mode 100644 configs/T2080RDB_NAND_defconfig delete mode 100644 configs/T2080RDB_SDCARD_defconfig delete mode 100644 configs/T2080RDB_SECURE_BOOT_defconfig delete mode 100644 configs/T2080RDB_SPIFLASH_defconfig delete mode 100644 configs/T2080RDB_SRIO_PCIE_BOOT_defconfig delete mode 100644 configs/T2080RDB_defconfig delete mode 100644 include/configs/T208xRDB.h