| Message ID | 20200610103658.96678-3-jagan@amarulasolutions.com |
|---|---|
| State | New |
| Headers | show |
| Series |
|
| Related | show |
On 2020/6/10 下午6:36, Jagan Teki wrote: > VMARC RK3399Pro SOM is a standard SMARC SOM design with > Rockchip RK3399Pro SoC, which is designed by Vamrs. > > Specification: > - Rockchip RK3399Pro > - PMIC: RK809-3 > - SD slot, 16GiB eMMC > - 2xUSB-2.0, 1xUSB3.0 > - USB-C for power supply > - Ethernet, PCIe > - HDMI, MIPI-DSI/CSI, eDP > > Add initial support for VMARC RK3399Pro SOM, this would use > with associated carrier board. > > Sync this dtsi from linux-next v5.7-rc1. > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Thanks, - Kever > --- > arch/arm/dts/rk3399pro-vmarc-som.dtsi | 333 ++++++++++++++++++++++++++ > 1 file changed, 333 insertions(+) > create mode 100644 arch/arm/dts/rk3399pro-vmarc-som.dtsi > > diff --git a/arch/arm/dts/rk3399pro-vmarc-som.dtsi b/arch/arm/dts/rk3399pro-vmarc-som.dtsi > new file mode 100644 > index 0000000000..0a516334f1 > --- /dev/null > +++ b/arch/arm/dts/rk3399pro-vmarc-som.dtsi > @@ -0,0 +1,333 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd > + * Copyright (c) 2019 Vamrs Limited > + * Copyright (c) 2019 Amarula Solutions(India) > + */ > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/pinctrl/rockchip.h> > +#include <dt-bindings/pwm/pwm.h> > + > +/ { > + compatible = "vamrs,rk3399pro-vmarc-som", "rockchip,rk3399pro"; > + > + clkin_gmac: external-gmac-clock { > + compatible = "fixed-clock"; > + clock-frequency = <125000000>; > + clock-output-names = "clkin_gmac"; > + #clock-cells = <0>; > + }; > + > + vcc12v_dcin: vcc12v-dcin-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vcc12v_dcin"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + }; > + > + vcc5v0_sys: vcc5v0-sys-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vcc5v0_sys"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&vcc12v_dcin>; > + }; > +}; > + > +&cpu_l0 { > + cpu-supply = <&vdd_cpu_l>; > +}; > + > +&cpu_l1 { > + cpu-supply = <&vdd_cpu_l>; > +}; > + > +&cpu_l2 { > + cpu-supply = <&vdd_cpu_l>; > +}; > + > +&cpu_l3 { > + cpu-supply = <&vdd_cpu_l>; > +}; > + > +&emmc_phy { > + status = "okay"; > +}; > + > +&gmac { > + assigned-clocks = <&cru SCLK_RMII_SRC>; > + assigned-clock-parents = <&clkin_gmac>; > + clock_in_out = "input"; > + phy-supply = <&vcc_lan>; > + phy-mode = "rgmii"; > + pinctrl-names = "default"; > + pinctrl-0 = <&rgmii_pins>; > + snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>; > + snps,reset-active-low; > + snps,reset-delays-us = <0 10000 50000>; > + tx_delay = <0x28>; > + rx_delay = <0x11>; > +}; > + > +&i2c0 { > + clock-frequency = <400000>; > + i2c-scl-rising-time-ns = <180>; > + i2c-scl-falling-time-ns = <30>; > + status = "okay"; > + > + rk809: pmic@20 { > + compatible = "rockchip,rk809"; > + reg = <0x20>; > + interrupt-parent = <&gpio1>; > + interrupts = <RK_PC2 IRQ_TYPE_LEVEL_LOW>; > + #clock-cells = <1>; > + clock-output-names = "rk808-clkout1", "rk808-clkout2"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pmic_int_l>; > + rockchip,system-power-controller; > + wakeup-source; > + > + vcc1-supply = <&vcc5v0_sys>; > + vcc2-supply = <&vcc5v0_sys>; > + vcc3-supply = <&vcc5v0_sys>; > + vcc4-supply = <&vcc5v0_sys>; > + vcc5-supply = <&vcc_buck5>; > + vcc6-supply = <&vcc_buck5>; > + vcc7-supply = <&vcc5v0_sys>; > + vcc8-supply = <&vcc3v3_sys>; > + vcc9-supply = <&vcc5v0_sys>; > + > + regulators { > + vdd_log: DCDC_REG1 { > + regulator-name = "vdd_log"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <750000>; > + regulator-max-microvolt = <1350000>; > + regulator-initial-mode = <0x2>; > + regulator-state-mem { > + regulator-off-in-suspend; > + regulator-suspend-microvolt = <900000>; > + }; > + }; > + > + vdd_cpu_l: DCDC_REG2 { > + regulator-name = "vdd_cpu_l"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <750000>; > + regulator-max-microvolt = <1350000>; > + regulator-ramp-delay = <6001>; > + regulator-initial-mode = <0x2>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc_ddr: DCDC_REG3 { > + regulator-name = "vcc_ddr"; > + regulator-always-on; > + regulator-boot-on; > + regulator-initial-mode = <0x2>; > + regulator-state-mem { > + regulator-on-in-suspend; > + }; > + }; > + > + vcc3v3_sys: DCDC_REG4 { > + regulator-name = "vcc3v3_sys"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-initial-mode = <0x2>; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <3300000>; > + }; > + }; > + > + vcc_buck5: DCDC_REG5 { > + regulator-name = "vcc_buck5"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <2200000>; > + regulator-max-microvolt = <2200000>; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <2200000>; > + }; > + }; > + > + vcca_0v9: LDO_REG1 { > + regulator-name = "vcca_0v9"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc_1v8: LDO_REG2 { > + regulator-name = "vcc_1v8"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1800000>; > + }; > + }; > + > + vcc_0v9: LDO_REG3 { > + regulator-name = "vcc_0v9"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <900000>; > + }; > + }; > + > + vcca_1v8: LDO_REG4 { > + regulator-name = "vcca_1v8"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1850000>; > + regulator-max-microvolt = <1850000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + /* > + * As per BSP, but schematic not showing any regulator > + * pin for LD05. > + */ > + vdd1v5_dvp: LDO_REG5 { > + regulator-name = "vdd1v5_dvp"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc_1v5: LDO_REG6 { > + regulator-name = "vcc_1v5"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vccio_3v0: LDO_REG7 { > + regulator-name = "vccio_3v0"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vccio_sd: LDO_REG8 { > + regulator-name = "vccio_sd"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + /* > + * As per BSP, but schematic not showing any regulator > + * pin for LD09. > + */ > + vcc_sd: LDO_REG9 { > + regulator-name = "vcc_sd"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc5v0_usb2: SWITCH_REG1 { > + regulator-name = "vcc5v0_usb2"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <5000000>; > + }; > + }; > + > + vccio_3v3: vcc_lan: SWITCH_REG2 { > + regulator-name = "vccio_3v3"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + }; > + }; > +}; > + > +&io_domains { > + status = "okay"; > + bt656-supply = <&vcca_1v8>; > + sdmmc-supply = <&vccio_sd>; > + gpio1830-supply = <&vccio_3v0>; > +}; > + > +&pmu_io_domains { > + status = "okay"; > + pmu1830-supply = <&vcc_1v8>; > +}; > + > +&sdhci { > + bus-width = <8>; > + mmc-hs400-1_8v; > + mmc-hs400-enhanced-strobe; > + non-removable; > + status = "okay"; > +}; > + > +&tsadc { > + status = "okay"; > + rockchip,hw-tshut-mode = <1>; > + rockchip,hw-tshut-polarity = <1>; > +}; > + > +&pinctrl { > + pmic { > + pmic_int_l: pmic-int-l { > + rockchip,pins = > + <1 RK_PC2 0 &pcfg_pull_up>; > + }; > + }; > +};
diff --git a/arch/arm/dts/rk3399pro-vmarc-som.dtsi b/arch/arm/dts/rk3399pro-vmarc-som.dtsi new file mode 100644 index 0000000000..0a516334f1 --- /dev/null +++ b/arch/arm/dts/rk3399pro-vmarc-som.dtsi @@ -0,0 +1,333 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2019 Vamrs Limited + * Copyright (c) 2019 Amarula Solutions(India) + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + compatible = "vamrs,rk3399pro-vmarc-som", "rockchip,rk3399pro"; + + clkin_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "clkin_gmac"; + #clock-cells = <0>; + }; + + vcc12v_dcin: vcc12v-dcin-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc12v_dcin"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; + + vcc5v0_sys: vcc5v0-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc12v_dcin>; + }; +}; + +&cpu_l0 { + cpu-supply = <&vdd_cpu_l>; +}; + +&cpu_l1 { + cpu-supply = <&vdd_cpu_l>; +}; + +&cpu_l2 { + cpu-supply = <&vdd_cpu_l>; +}; + +&cpu_l3 { + cpu-supply = <&vdd_cpu_l>; +}; + +&emmc_phy { + status = "okay"; +}; + +&gmac { + assigned-clocks = <&cru SCLK_RMII_SRC>; + assigned-clock-parents = <&clkin_gmac>; + clock_in_out = "input"; + phy-supply = <&vcc_lan>; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 50000>; + tx_delay = <0x28>; + rx_delay = <0x11>; +}; + +&i2c0 { + clock-frequency = <400000>; + i2c-scl-rising-time-ns = <180>; + i2c-scl-falling-time-ns = <30>; + status = "okay"; + + rk809: pmic@20 { + compatible = "rockchip,rk809"; + reg = <0x20>; + interrupt-parent = <&gpio1>; + interrupts = <RK_PC2 IRQ_TYPE_LEVEL_LOW>; + #clock-cells = <1>; + clock-output-names = "rk808-clkout1", "rk808-clkout2"; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l>; + rockchip,system-power-controller; + wakeup-source; + + vcc1-supply = <&vcc5v0_sys>; + vcc2-supply = <&vcc5v0_sys>; + vcc3-supply = <&vcc5v0_sys>; + vcc4-supply = <&vcc5v0_sys>; + vcc5-supply = <&vcc_buck5>; + vcc6-supply = <&vcc_buck5>; + vcc7-supply = <&vcc5v0_sys>; + vcc8-supply = <&vcc3v3_sys>; + vcc9-supply = <&vcc5v0_sys>; + + regulators { + vdd_log: DCDC_REG1 { + regulator-name = "vdd_log"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vdd_cpu_l: DCDC_REG2 { + regulator-name = "vdd_cpu_l"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc3v3_sys: DCDC_REG4 { + regulator-name = "vcc3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_buck5: DCDC_REG5 { + regulator-name = "vcc_buck5"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <2200000>; + }; + }; + + vcca_0v9: LDO_REG1 { + regulator-name = "vcca_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8: LDO_REG2 { + regulator-name = "vcc_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc_0v9: LDO_REG3 { + regulator-name = "vcc_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vcca_1v8: LDO_REG4 { + regulator-name = "vcca_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1850000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* + * As per BSP, but schematic not showing any regulator + * pin for LD05. + */ + vdd1v5_dvp: LDO_REG5 { + regulator-name = "vdd1v5_dvp"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v5: LDO_REG6 { + regulator-name = "vcc_1v5"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_3v0: LDO_REG7 { + regulator-name = "vccio_3v0"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG8 { + regulator-name = "vccio_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* + * As per BSP, but schematic not showing any regulator + * pin for LD09. + */ + vcc_sd: LDO_REG9 { + regulator-name = "vcc_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc5v0_usb2: SWITCH_REG1 { + regulator-name = "vcc5v0_usb2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <5000000>; + }; + }; + + vccio_3v3: vcc_lan: SWITCH_REG2 { + regulator-name = "vccio_3v3"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&io_domains { + status = "okay"; + bt656-supply = <&vcca_1v8>; + sdmmc-supply = <&vccio_sd>; + gpio1830-supply = <&vccio_3v0>; +}; + +&pmu_io_domains { + status = "okay"; + pmu1830-supply = <&vcc_1v8>; +}; + +&sdhci { + bus-width = <8>; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + non-removable; + status = "okay"; +}; + +&tsadc { + status = "okay"; + rockchip,hw-tshut-mode = <1>; + rockchip,hw-tshut-polarity = <1>; +}; + +&pinctrl { + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = + <1 RK_PC2 0 &pcfg_pull_up>; + }; + }; +};
VMARC RK3399Pro SOM is a standard SMARC SOM design with Rockchip RK3399Pro SoC, which is designed by Vamrs. Specification: - Rockchip RK3399Pro - PMIC: RK809-3 - SD slot, 16GiB eMMC - 2xUSB-2.0, 1xUSB3.0 - USB-C for power supply - Ethernet, PCIe - HDMI, MIPI-DSI/CSI, eDP Add initial support for VMARC RK3399Pro SOM, this would use with associated carrier board. Sync this dtsi from linux-next v5.7-rc1. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- arch/arm/dts/rk3399pro-vmarc-som.dtsi | 333 ++++++++++++++++++++++++++ 1 file changed, 333 insertions(+) create mode 100644 arch/arm/dts/rk3399pro-vmarc-som.dtsi