@@ -6,6 +6,11 @@
*/
/ {
+ aliases {
+ mmc1 = &sdmmc;
+ mmc2 = &sdio;
+ };
+
vcc5v0_sys: vcc5v0-sys {
compatible = "regulator-fixed";
regulator-name = "vcc5v0_sys"; /* +5V */
@@ -14,6 +19,63 @@
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&xin32k>;
+ clock-names = "ext_clock";
+ post-power-on-delay-ms = <80>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ };
+
+ vcc3v3_btreg: vcc3v3-btreg {
+ compatible = "regulator-gpio";
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_enable_h>;
+ regulator-name = "btreg-gpio-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ states = <3300000 0x0>;
+ };
+
+ vcc3v3_rf_aux_mod: vcc3v3-rf-aux-mod {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_rf_aux_mod";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ xin32k: xin32k {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ };
+};
+
+&sdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ clock-frequency = <50000000>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ sd-uhs-sdr104;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+ };
};
&gmac {
@@ -25,6 +87,10 @@
status = "okay";
};
+&pwm0 {
+ status = "okay";
+};
+
&sdmmc {
cap-sd-highspeed;
card-detect-delay = <800>;
@@ -33,7 +99,31 @@
status = "okay";
};
+&u2phy {
+ status = "okay";
+
+ u2phy_host: host-port {
+ status = "okay";
+ };
+
+ u2phy_otg: otg-port {
+ status = "okay";
+ };
+};
+
&uart2 {
pinctrl-0 = <&uart2m1_xfer>;
status = "okay";
};
+
+&usb20_otg {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
@@ -6,3 +6,25 @@
*/
#include "px30-engicam-common.dtsi"
+
+&pinctrl {
+ bt {
+ bt_enable_h: bt-enable-h {
+ rockchip,pins = <1 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdio_pwrseq {
+ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+};
+
+&vcc3v3_btreg {
+ enable-gpio = <&gpio1 RK_PC3 GPIO_ACTIVE_HIGH>;
+};
@@ -5,3 +5,62 @@
*/
#include "px30-engicam-common.dtsi"
+
+/ {
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm0 0 25000 0>;
+ };
+
+ panel {
+ compatible = "yes-optoelectronics,ytc700tlag-05-201c";
+ backlight = <&backlight>;
+ data-mapping = "vesa-24";
+ power-supply = <&vcc3v3_lcd>;
+
+ port {
+ panel_in_lvds: endpoint {
+ remote-endpoint = <&lvds_out_panel>;
+ };
+ };
+ };
+};
+
+&display_subsystem {
+ status = "okay";
+};
+
+&dsi_dphy {
+ status = "okay";
+};
+
+/* LVDS_B(secondary) */
+&lvds {
+ status = "okay";
+
+ ports {
+ port@1 {
+ reg = <1>;
+
+ lvds_out_panel: endpoint {
+ remote-endpoint = <&panel_in_lvds>;
+ };
+ };
+ };
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "px30.dtsi"
+#include "px30-engicam-ctouch2.dtsi"
+#include "px30-engicam-px30-core.dtsi"
+
+/ {
+ model = "Engicam PX30.Core C.TOUCH 2.0 10.1\" Open Frame";
+ compatible = "engicam,px30-core-ctouch2-of10", "engicam,px30-core",
+ "rockchip,px30";
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm0 0 25000 0>;
+ };
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ panel {
+ compatible = "ampire,am-1280800n3tzqw-t00h";
+ backlight = <&backlight>;
+ power-supply = <&vcc3v3_lcd>;
+ data-mapping = "vesa-24";
+
+ port {
+ panel_in_lvds: endpoint {
+ remote-endpoint = <&lvds_out_panel>;
+ };
+ };
+ };
+};
+
+&display_subsystem {
+ status = "okay";
+};
+
+&dsi_dphy {
+ status = "okay";
+};
+
+&lvds {
+ status = "okay";
+
+ ports {
+ port@1 {
+ reg = <1>;
+
+ lvds_out_panel: endpoint {
+ remote-endpoint = <&panel_in_lvds>;
+ };
+ };
+ };
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
@@ -19,3 +19,25 @@
stdout-path = "serial2:115200n8";
};
};
+
+&pinctrl {
+ bt {
+ bt_enable_h: bt-enable-h {
+ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <1 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdio_pwrseq {
+ reset-gpios = <&gpio1 RK_PC3 GPIO_ACTIVE_LOW>;
+};
+
+&vcc3v3_btreg {
+ enable-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
+};
@@ -13,8 +13,14 @@
model = "Rockchip PX30 EVB";
compatible = "rockchip,px30-evb", "rockchip,px30";
+ aliases {
+ mmc0 = &sdmmc;
+ mmc1 = &sdio;
+ mmc2 = &emmc;
+ };
+
chosen {
- stdout-path = "serial2:115200n8";
+ stdout-path = "serial5:115200n8";
};
adc-keys {
@@ -126,22 +132,15 @@
};
panel@0 {
- compatible = "sitronix,st7703";
+ compatible = "xinpeng,xpp055c272";
reg = <0>;
backlight = <&backlight>;
iovcc-supply = <&vcc_1v8>;
vci-supply = <&vcc3v3_lcd>;
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- mipi_in_panel: endpoint {
- remote-endpoint = <&mipi_out_panel>;
- };
+ port {
+ mipi_in_panel: endpoint {
+ remote-endpoint = <&mipi_out_panel>;
};
};
};
@@ -152,7 +151,6 @@
};
&emmc {
- bus-width = <8>;
cap-mmc-highspeed;
mmc-hs200-1_8v;
non-removable;
@@ -171,6 +169,11 @@
status = "okay";
};
+&gpu {
+ mali-supply = <&vdd_log>;
+ status = "okay";
+};
+
&i2c0 {
status = "okay";
@@ -388,6 +391,43 @@
};
};
+&i2c1 {
+ status = "okay";
+
+ sensor@d {
+ compatible = "asahi-kasei,ak8963";
+ reg = <0x0d>;
+ gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+ vdd-supply = <&vcc3v0_pmu>;
+ mount-matrix = "1", /* x0 */
+ "0", /* y0 */
+ "0", /* z0 */
+ "0", /* x1 */
+ "1", /* y1 */
+ "0", /* z1 */
+ "0", /* x2 */
+ "0", /* y2 */
+ "1"; /* z2 */
+ };
+
+ touchscreen@14 {
+ compatible = "goodix,gt1151";
+ reg = <0x14>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
+ irq-gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
+ VDDIO-supply = <&vcc3v3_lcd>;
+ };
+
+ sensor@4c {
+ compatible = "fsl,mma7660";
+ reg = <0x4c>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB7 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
&i2s1_2ch {
status = "okay";
};
@@ -464,7 +504,6 @@
};
&sdmmc {
- bus-width = <4>;
cap-mmc-highspeed;
cap-sd-highspeed;
card-detect-delay = <800>;
@@ -474,10 +513,10 @@
sd-uhs-sdr104;
vmmc-supply = <&vcc_sd>;
vqmmc-supply = <&vccio_sd>;
+ status = "okay";
};
&sdio {
- bus-width = <4>;
cap-sd-highspeed;
keep-power-in-suspend;
non-removable;
@@ -486,13 +525,27 @@
status = "okay";
};
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_xfer &uart1_cts>;
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <1>;
+ status = "okay";
+};
+
+&u2phy {
status = "okay";
+
+ u2phy_host: host-port {
+ status = "okay";
+ };
+
+ u2phy_otg: otg-port {
+ status = "okay";
+ };
};
-&uart2 {
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_xfer &uart1_cts>;
status = "okay";
};
@@ -143,7 +143,7 @@
};
arm-pmu {
- compatible = "arm,cortex-a53-pmu";
+ compatible = "arm,cortex-a35-pmu";
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
@@ -244,28 +244,31 @@
#size-cells = <0>;
/* These power domains are grouped by VD_LOGIC */
- pd_usb@PX30_PD_USB {
+ power-domain@PX30_PD_USB {
reg = <PX30_PD_USB>;
clocks = <&cru HCLK_HOST>,
<&cru HCLK_OTG>,
<&cru SCLK_OTG_ADP>;
pm_qos = <&qos_usb_host>, <&qos_usb_otg>;
+ #power-domain-cells = <0>;
};
- pd_sdcard@PX30_PD_SDCARD {
+ power-domain@PX30_PD_SDCARD {
reg = <PX30_PD_SDCARD>;
clocks = <&cru HCLK_SDMMC>,
<&cru SCLK_SDMMC>;
pm_qos = <&qos_sdmmc>;
+ #power-domain-cells = <0>;
};
- pd_gmac@PX30_PD_GMAC {
+ power-domain@PX30_PD_GMAC {
reg = <PX30_PD_GMAC>;
clocks = <&cru ACLK_GMAC>,
<&cru PCLK_GMAC>,
<&cru SCLK_MAC_REF>,
<&cru SCLK_GMAC_RX_TX>;
pm_qos = <&qos_gmac>;
+ #power-domain-cells = <0>;
};
- pd_mmc_nand@PX30_PD_MMC_NAND {
+ power-domain@PX30_PD_MMC_NAND {
reg = <PX30_PD_MMC_NAND>;
clocks = <&cru HCLK_NANDC>,
<&cru HCLK_EMMC>,
@@ -277,15 +280,17 @@
<&cru SCLK_SFC>;
pm_qos = <&qos_emmc>, <&qos_nand>,
<&qos_sdio>, <&qos_sfc>;
+ #power-domain-cells = <0>;
};
- pd_vpu@PX30_PD_VPU {
+ power-domain@PX30_PD_VPU {
reg = <PX30_PD_VPU>;
clocks = <&cru ACLK_VPU>,
<&cru HCLK_VPU>,
<&cru SCLK_CORE_VPU>;
pm_qos = <&qos_vpu>, <&qos_vpu_r128>;
+ #power-domain-cells = <0>;
};
- pd_vo@PX30_PD_VO {
+ power-domain@PX30_PD_VO {
reg = <PX30_PD_VO>;
clocks = <&cru ACLK_RGA>,
<&cru ACLK_VOPB>,
@@ -300,8 +305,9 @@
<&cru SCLK_VOPB_PWM>;
pm_qos = <&qos_rga_rd>, <&qos_rga_wr>,
<&qos_vop_m0>, <&qos_vop_m1>;
+ #power-domain-cells = <0>;
};
- pd_vi@PX30_PD_VI {
+ power-domain@PX30_PD_VI {
reg = <PX30_PD_VI>;
clocks = <&cru ACLK_CIF>,
<&cru ACLK_ISP>,
@@ -311,11 +317,13 @@
pm_qos = <&qos_isp_128>, <&qos_isp_rd>,
<&qos_isp_wr>, <&qos_isp_m1>,
<&qos_vip>;
+ #power-domain-cells = <0>;
};
- pd_gpu@PX30_PD_GPU {
+ power-domain@PX30_PD_GPU {
reg = <PX30_PD_GPU>;
clocks = <&cru SCLK_GPU>;
pm_qos = <&qos_gpu>;
+ #power-domain-cells = <0>;
};
};
};
@@ -600,7 +608,7 @@
};
wdt: watchdog@ff1e0000 {
- compatible = "snps,dw-wdt";
+ compatible = "rockchip,px30-wdt", "snps,dw-wdt";
reg = <0x0 0xff1e0000 0x0 0x100>;
clocks = <&cru PCLK_WDT_NS>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
@@ -703,21 +711,15 @@
clock-names = "pclk", "timer";
};
- amba {
- compatible = "simple-bus";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- dmac: dmac@ff240000 {
- compatible = "arm,pl330", "arm,primecell";
- reg = <0x0 0xff240000 0x0 0x4000>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru ACLK_DMAC>;
- clock-names = "apb_pclk";
- #dma-cells = <1>;
- };
+ dmac: dmac@ff240000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x0 0xff240000 0x0 0x4000>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ arm,pl330-periph-burst;
+ clocks = <&cru ACLK_DMAC>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
};
tsadc: tsadc@ff280000 {
@@ -733,9 +735,9 @@
rockchip,grf = <&grf>;
rockchip,hw-tshut-temp = <120000>;
pinctrl-names = "init", "default", "sleep";
- pinctrl-0 = <&tsadc_otp_gpio>;
+ pinctrl-0 = <&tsadc_otp_pin>;
pinctrl-1 = <&tsadc_otp_out>;
- pinctrl-2 = <&tsadc_otp_gpio>;
+ pinctrl-2 = <&tsadc_otp_pin>;
#thermal-sensor-cells = <1>;
status = "disabled";
};
@@ -784,6 +786,16 @@
rockchip,grf = <&grf>;
#clock-cells = <1>;
#reset-cells = <1>;
+
+ assigned-clocks = <&cru PLL_NPLL>,
+ <&cru ACLK_BUS_PRE>, <&cru ACLK_PERI_PRE>,
+ <&cru HCLK_BUS_PRE>, <&cru HCLK_PERI_PRE>,
+ <&cru PCLK_BUS_PRE>, <&cru SCLK_GPU>;
+
+ assigned-clock-rates = <1188000000>,
+ <200000000>, <200000000>,
+ <150000000>, <150000000>,
+ <100000000>, <200000000>;
};
pmucru: clock-controller@ff2bc000 {
@@ -794,6 +806,13 @@
rockchip,grf = <&grf>;
#clock-cells = <1>;
#reset-cells = <1>;
+
+ assigned-clocks =
+ <&pmucru PLL_GPLL>, <&pmucru PCLK_PMU_PRE>,
+ <&pmucru SCLK_WIFI_PMU>;
+ assigned-clock-rates =
+ <1200000000>, <100000000>,
+ <26000000>;
};
usb2phy_grf: syscon@ff2c0000 {
@@ -803,7 +822,7 @@
#address-cells = <1>;
#size-cells = <1>;
- u2phy: usb2-phy@100 {
+ u2phy: usb2phy@100 {
compatible = "rockchip,px30-usb2phy";
reg = <0x100 0x20>;
clocks = <&pmucru SCLK_USBPHY_REF>;
@@ -856,7 +875,6 @@
g-np-tx-fifo-size = <16>;
g-rx-fifo-size = <280>;
g-tx-fifo-size = <256 128 128 64 32 16>;
- g-use-dma;
phys = <&u2phy_otg>;
phy-names = "usb2-phy";
power-domains = <&power PX30_PD_USB>;
@@ -868,7 +886,6 @@
reg = <0x0 0xff340000 0x0 0x10000>;
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_HOST>;
- clock-names = "usbhost";
phys = <&u2phy_host>;
phy-names = "usb";
power-domains = <&power PX30_PD_USB>;
@@ -880,7 +897,6 @@
reg = <0x0 0xff350000 0x0 0x10000>;
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_HOST>;
- clock-names = "usbhost";
phys = <&u2phy_host>;
phy-names = "usb";
power-domains = <&power PX30_PD_USB>;
@@ -910,13 +926,14 @@
status = "disabled";
};
- sdmmc: dwmmc@ff370000 {
+ sdmmc: mmc@ff370000 {
compatible = "rockchip,px30-dw-mshc", "rockchip,rk3288-dw-mshc";
reg = <0x0 0xff370000 0x0 0x4000>;
interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
<&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
- clock-names = "biu", "ciu", "ciu-drv", "ciu-sample";
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ bus-width = <4>;
fifo-depth = <0x100>;
max-frequency = <150000000>;
pinctrl-names = "default";
@@ -925,13 +942,14 @@
status = "disabled";
};
- sdio: dwmmc@ff380000 {
+ sdio: mmc@ff380000 {
compatible = "rockchip,px30-dw-mshc", "rockchip,rk3288-dw-mshc";
reg = <0x0 0xff380000 0x0 0x4000>;
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
<&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
- clock-names = "biu", "ciu", "ciu-drv", "ciu-sample";
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ bus-width = <4>;
fifo-depth = <0x100>;
max-frequency = <150000000>;
pinctrl-names = "default";
@@ -940,13 +958,14 @@
status = "disabled";
};
- emmc: dwmmc@ff390000 {
+ emmc: mmc@ff390000 {
compatible = "rockchip,px30-dw-mshc", "rockchip,rk3288-dw-mshc";
reg = <0x0 0xff390000 0x0 0x4000>;
interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
<&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
- clock-names = "biu", "ciu", "ciu-drv", "ciu-sample";
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ bus-width = <8>;
fifo-depth = <0x100>;
max-frequency = <150000000>;
pinctrl-names = "default";
@@ -967,6 +986,42 @@
status = "disabled";
};
+ nfc: nand-controller@ff3b0000 {
+ compatible = "rockchip,px30-nfc";
+ reg = <0x0 0xff3b0000 0x0 0x4000>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>;
+ clock-names = "ahb", "nfc";
+ assigned-clocks = <&cru SCLK_NANDC>;
+ assigned-clock-rates = <150000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_cs0
+ &flash_rdn &flash_rdy &flash_wrn &flash_dqs>;
+ power-domains = <&power PX30_PD_MMC_NAND>;
+ status = "disabled";
+ };
+
+ gpu_opp_table: opp-table2 {
+ compatible = "operating-points-v2";
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ opp-microvolt = <950000>;
+ };
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ opp-microvolt = <975000>;
+ };
+ opp-400000000 {
+ opp-hz = /bits/ 64 <400000000>;
+ opp-microvolt = <1050000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <1125000>;
+ };
+ };
+
gpu: gpu@ff400000 {
compatible = "rockchip,px30-mali", "arm,mali-bifrost";
reg = <0x0 0xff400000 0x0 0x4000>;
@@ -977,6 +1032,7 @@
clocks = <&cru SCLK_GPU>;
#cooling-cells = <2>;
power-domains = <&power PX30_PD_GPU>;
+ operating-points-v2 = <&gpu_opp_table>;
status = "disabled";
};
@@ -1029,7 +1085,6 @@
reset-names = "axi", "ahb", "dclk";
iommus = <&vopb_mmu>;
power-domains = <&power PX30_PD_VO>;
- rockchip,grf = <&grf>;
status = "disabled";
vopb_out: port {
@@ -1052,7 +1107,6 @@
compatible = "rockchip,iommu";
reg = <0x0 0xff460f00 0x0 0x100>;
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "vopb_mmu";
clocks = <&cru ACLK_VOPB>, <&cru HCLK_VOPB>;
clock-names = "aclk", "iface";
power-domains = <&power PX30_PD_VO>;
@@ -1071,7 +1125,6 @@
reset-names = "axi", "ahb", "dclk";
iommus = <&vopl_mmu>;
power-domains = <&power PX30_PD_VO>;
- rockchip,grf = <&grf>;
status = "disabled";
vopl_out: port {
@@ -1093,8 +1146,7 @@
vopl_mmu: iommu@ff470f00 {
compatible = "rockchip,iommu";
reg = <0x0 0xff470f00 0x0 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "vopl_mmu";
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru ACLK_VOPL>, <&cru HCLK_VOPL>;
clock-names = "aclk", "iface";
power-domains = <&power PX30_PD_VO>;
@@ -1103,102 +1155,102 @@
};
qos_gmac: qos@ff518000 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff518000 0x0 0x20>;
};
qos_gpu: qos@ff520000 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff520000 0x0 0x20>;
};
qos_sdmmc: qos@ff52c000 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff52c000 0x0 0x20>;
};
qos_emmc: qos@ff538000 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff538000 0x0 0x20>;
};
qos_nand: qos@ff538080 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff538080 0x0 0x20>;
};
qos_sdio: qos@ff538100 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff538100 0x0 0x20>;
};
qos_sfc: qos@ff538180 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff538180 0x0 0x20>;
};
qos_usb_host: qos@ff540000 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff540000 0x0 0x20>;
};
qos_usb_otg: qos@ff540080 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff540080 0x0 0x20>;
};
qos_isp_128: qos@ff548000 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff548000 0x0 0x20>;
};
qos_isp_rd: qos@ff548080 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff548080 0x0 0x20>;
};
qos_isp_wr: qos@ff548100 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff548100 0x0 0x20>;
};
qos_isp_m1: qos@ff548180 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff548180 0x0 0x20>;
};
qos_vip: qos@ff548200 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff548200 0x0 0x20>;
};
qos_rga_rd: qos@ff550000 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff550000 0x0 0x20>;
};
qos_rga_wr: qos@ff550080 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff550080 0x0 0x20>;
};
qos_vop_m0: qos@ff550100 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff550100 0x0 0x20>;
};
qos_vop_m1: qos@ff550180 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff550180 0x0 0x20>;
};
qos_vpu: qos@ff558000 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff558000 0x0 0x20>;
};
qos_vpu_r128: qos@ff558080 {
- compatible = "syscon";
+ compatible = "rockchip,px30-qos", "syscon";
reg = <0x0 0xff558080 0x0 0x20>;
};
@@ -1370,7 +1422,7 @@
};
tsadc {
- tsadc_otp_gpio: tsadc-otp-gpio {
+ tsadc_otp_pin: tsadc-otp-pin {
rockchip,pins =
<0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
};