@@ -600,6 +600,30 @@ static void dwc3_core_exit_mode(struct dwc3 *dwc)
}
}
+static void dwc3_uboot_hsphy_mode(struct dwc3_device *dwc3_dev, struct dwc3 *dwc)
+{
+ enum usb_phy_interface hsphy_mode = dwc3_dev->hsphy_mode;
+ u32 reg;
+
+ /* Set dwc3 usb2 phy config */
+ reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
+ reg |= DWC3_GUSB2PHYCFG_PHYIF;
+ reg &= ~DWC3_GUSB2PHYCFG_USBTRDTIM_MASK;
+
+ switch (hsphy_mode) {
+ case USBPHY_INTERFACE_MODE_UTMI:
+ reg |= DWC3_GUSB2PHYCFG_USBTRDTIM_8BIT;
+ break;
+ case USBPHY_INTERFACE_MODE_UTMIW:
+ reg |= DWC3_GUSB2PHYCFG_USBTRDTIM_16BIT;
+ break;
+ default:
+ break;
+ }
+
+ dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
+}
+
#define DWC3_ALIGN_MASK (16 - 1)
/**
@@ -708,6 +732,8 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev)
goto err0;
}
+ dwc3_uboot_hsphy_mode(dwc3_dev, dwc);
+
ret = dwc3_event_buffers_setup(dwc);
if (ret) {
dev_err(dwc->dev, "failed to setup event buffers\n");
@@ -162,6 +162,18 @@
/* Global USB2 PHY Configuration Register */
#define DWC3_GUSB2PHYCFG_PHYSOFTRST (1 << 31)
#define DWC3_GUSB2PHYCFG_SUSPHY (1 << 6)
+#define DWC3_GUSB2PHYCFG_PHYIF (1 << 3)
+
+/* Global USB2 PHY Configuration Mask */
+#define DWC3_GUSB2PHYCFG_USBTRDTIM_MASK (0xf << 10)
+
+/* Global USB2 PHY Configuration Offset */
+#define DWC3_GUSB2PHYCFG_USBTRDTIM_OFFSET 10
+
+#define DWC3_GUSB2PHYCFG_USBTRDTIM_16BIT (0x5 << \
+ DWC3_GUSB2PHYCFG_USBTRDTIM_OFFSET)
+#define DWC3_GUSB2PHYCFG_USBTRDTIM_8BIT (0x9 << \
+ DWC3_GUSB2PHYCFG_USBTRDTIM_OFFSET)
/* Global USB3 PIPE Control Register */
#define DWC3_GUSB3PIPECTL_PHYSOFTRST (1 << 31)
@@ -10,10 +10,12 @@
#define __DWC3_UBOOT_H_
#include <linux/usb/otg.h>
+#include <linux/usb/phy.h>
struct dwc3_device {
unsigned long base;
enum usb_dr_mode dr_mode;
+ enum usb_phy_interface hsphy_mode;
u32 maximum_speed;
unsigned tx_fifo_resize:1;
unsigned has_lpm_erratum;
new file mode 100644
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * USB PHY defines
+ *
+ * These APIs may be used between USB controllers. USB device drivers
+ * (for either host or peripheral roles) don't use these calls; they
+ * continue to use just usb_device and usb_gadget.
+ */
+
+#ifndef __LINUX_USB_PHY_H
+#define __LINUX_USB_PHY_H
+
+enum usb_phy_interface {
+ USBPHY_INTERFACE_MODE_UNKNOWN,
+ USBPHY_INTERFACE_MODE_UTMI,
+ USBPHY_INTERFACE_MODE_UTMIW,
+};
+
+#endif /* __LINUX_USB_PHY_H */
U-Boot has two different variants of dwc3 initializations, - with dm variant gadget, so the respective dm driver would call the dwc3_init in core. - with non-dm variant gadget, so the usage board file would call dwc3_uboot_init in core. The driver probe would handle all respective gadget properties including phy interface via phy_type property and then trigger dwc3_init for dm-variant gadgets. So, to support the phy interface for non-dm variant gadgets, the better option is dwc3_uboot_init since there is no dedicated controller for non-dm variant gadgets. This patch support for adding phy interface like 8/16-bit UTMI+ code for dwc3_uboot. This change used Linux phy.h enum list, to make proper code compatibility. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- drivers/usb/dwc3/core.c | 26 ++++++++++++++++++++++++++ drivers/usb/dwc3/core.h | 12 ++++++++++++ include/dwc3-uboot.h | 2 ++ include/linux/usb/phy.h | 19 +++++++++++++++++++ 4 files changed, 59 insertions(+) create mode 100644 include/linux/usb/phy.h