diff mbox series

[v4] arm64: dts: imx8mm-evk: add pwm1/backlight support

Message ID 20220413213313.11511-1-tommaso.merciai@amarulasolutions.com
State New
Headers
Series [v4] arm64: dts: imx8mm-evk: add pwm1/backlight support |

Commit Message

Tommaso Merciai April 13, 2022, 9:33 p.m. UTC 
Add pwm1/backlight support nodes for imx8mm_evk board.
Align with u-boot dts

References:
 - https://patchwork.ozlabs.org/project/uboot/patch/20220326111911.13720-9-tommaso.merciai@amarulasolutions.com/

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
---
Changes since v1:
 - Fix commit body
 - Enable pwm, backlight

Changes since v2:
 - Remove status okay from pwm1,backlight (enable as default)

Changes since v3:
 - Remove status okay only from backlight (enable as default), pwm1 is disabled
   on imx8mm.dtsi, we need to enable it

 arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi | 20 +++++++++++++++++++
 1 file changed, 20 insertions(+)

Comments

Shawn Guo April 18, 2022, 12:12 p.m. UTC | #1 
On Wed, Apr 13, 2022 at 11:33:11PM +0200, Tommaso Merciai wrote:
> Add pwm1/backlight support nodes for imx8mm_evk board.
> Align with u-boot dts
> 
> References:
>  - https://patchwork.ozlabs.org/project/uboot/patch/20220326111911.13720-9-tommaso.merciai@amarulasolutions.com/
> 
> Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>

Applied, thanks!
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
index 6d67df7692f1..6a209395452a 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
@@ -59,6 +59,14 @@  reg_usdhc2_vmmc: regulator-usdhc2 {
 		enable-active-high;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <250>;
+	};
+
 	ir-receiver {
 		compatible = "gpio-ir-receiver";
 		gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
@@ -395,6 +403,12 @@  &wdog1 {
 	status = "okay";
 };
 
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_backlight>;
+	status = "okay";
+};
+
 &iomuxc {
 	pinctrl_fec1: fec1grp {
 		fsl,pins = <
@@ -549,4 +563,10 @@  pinctrl_wdog: wdoggrp {
 			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0x166
 		>;
 	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT	0x06
+		>;
+	};
 };