diff mbox series

[v4,12/12] rk3566: radxa-cm3: Enable USB2.0, USB3.0 support

Message ID 20230217115845.75303-13-jagan@amarulasolutions.com
State New
Headers
Series rockchip: Add Radxa CM3 support |

Commit Message

Jagan Teki Feb. 17, 2023, 11:58 a.m. UTC 
From: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>

=> usb start
starting USB...
Bus usb@fd000000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fd800000: USB EHCI 1.00
scanning bus usb@fd000000 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning bus usb@fd800000 for devices... 4 USB Device(s) found
       scanning usb for storage devices... 2 Storage Device(s) found
=> usb tree
USB device tree:
  1  Hub (5 Gb/s, 0mA)
  |  U-Boot XHCI Host Controller
  |
  +-2  Mass Storage (5 Gb/s, 224mA)
       SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5

  1  Hub (480 Mb/s, 0mA)
  |  u-boot EHCI Host Controller
  |
  +-2  Hub (480 Mb/s, 100mA)
    |   USB 2.0 Hub
    |
    +-3  Mass Storage (480 Mb/s, 500mA)
    |    JetFlash Mass Storage Device 19M7I4ZQFTSC08SU
    |
    +-4  Human Interface (12 Mb/s, 98mA)
         Logitech USB Receiver

Co-developed-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
---
 configs/radxa-cm3-io-rk3566_defconfig | 11 +++++++++++
 1 file changed, 11 insertions(+)

Comments

Kever Yang Feb. 21, 2023, 9:33 a.m. UTC | #1 
On 2023/2/17 19:58, Jagan Teki wrote:
> From: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
>
> => usb start
> starting USB...
> Bus usb@fd000000: Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> Bus usb@fd800000: USB EHCI 1.00
> scanning bus usb@fd000000 for devices... cannot reset port 1!?
> 2 USB Device(s) found
> scanning bus usb@fd800000 for devices... 4 USB Device(s) found
>         scanning usb for storage devices... 2 Storage Device(s) found
> => usb tree
> USB device tree:
>    1  Hub (5 Gb/s, 0mA)
>    |  U-Boot XHCI Host Controller
>    |
>    +-2  Mass Storage (5 Gb/s, 224mA)
>         SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5
>
>    1  Hub (480 Mb/s, 0mA)
>    |  u-boot EHCI Host Controller
>    |
>    +-2  Hub (480 Mb/s, 100mA)
>      |   USB 2.0 Hub
>      |
>      +-3  Mass Storage (480 Mb/s, 500mA)
>      |    JetFlash Mass Storage Device 19M7I4ZQFTSC08SU
>      |
>      +-4  Human Interface (12 Mb/s, 98mA)
>           Logitech USB Receiver
>
> Co-developed-by: Suniel Mahesh <sunil@amarulasolutions.com>
> Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
> Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

Thanks,
- Kever
> ---
>   configs/radxa-cm3-io-rk3566_defconfig | 11 +++++++++++
>   1 file changed, 11 insertions(+)
>
> diff --git a/configs/radxa-cm3-io-rk3566_defconfig b/configs/radxa-cm3-io-rk3566_defconfig
> index a79d9b25e3..2100cf2cb2 100644
> --- a/configs/radxa-cm3-io-rk3566_defconfig
> +++ b/configs/radxa-cm3-io-rk3566_defconfig
> @@ -38,6 +38,7 @@ CONFIG_SPL_STACK_R=y
>   CONFIG_SPL_ATF=y
>   CONFIG_CMD_GPT=y
>   CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
>   # CONFIG_CMD_SETEXPR is not set
>   # CONFIG_SPL_DOS_PARTITION is not set
>   CONFIG_SPL_OF_CONTROL=y
> @@ -57,10 +58,20 @@ CONFIG_MMC_SDHCI_SDMA=y
>   CONFIG_MMC_SDHCI_ROCKCHIP=y
>   CONFIG_ETH_DESIGNWARE=y
>   CONFIG_GMAC_ROCKCHIP=y
> +CONFIG_PHY_ROCKCHIP_INNO_USB2=y
> +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
>   CONFIG_REGULATOR_PWM=y
> +CONFIG_DM_REGULATOR_GPIO=y
>   CONFIG_PWM_ROCKCHIP=y
>   CONFIG_SPL_RAM=y
>   CONFIG_BAUDRATE=1500000
>   CONFIG_DEBUG_UART_SHIFT=2
>   CONFIG_SYSRESET=y
> +CONFIG_USB=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_XHCI_DWC3=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_DWC3=y
> +CONFIG_USB_DWC3_GENERIC=y
>   CONFIG_ERRNO_STR=y
diff mbox series

Patch

diff --git a/configs/radxa-cm3-io-rk3566_defconfig b/configs/radxa-cm3-io-rk3566_defconfig
index a79d9b25e3..2100cf2cb2 100644
--- a/configs/radxa-cm3-io-rk3566_defconfig
+++ b/configs/radxa-cm3-io-rk3566_defconfig
@@ -38,6 +38,7 @@  CONFIG_SPL_STACK_R=y
 CONFIG_SPL_ATF=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 # CONFIG_SPL_DOS_PARTITION is not set
 CONFIG_SPL_OF_CONTROL=y
@@ -57,10 +58,20 @@  CONFIG_MMC_SDHCI_SDMA=y
 CONFIG_MMC_SDHCI_ROCKCHIP=y
 CONFIG_ETH_DESIGNWARE=y
 CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
 CONFIG_REGULATOR_PWM=y
+CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_PWM_ROCKCHIP=y
 CONFIG_SPL_RAM=y
 CONFIG_BAUDRATE=1500000
 CONFIG_DEBUG_UART_SHIFT=2
 CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
 CONFIG_ERRNO_STR=y