diff mbox series

[v3] arm64: dts: imx8mm-evk: add pwm1/backlight support

Message ID 20220413160900.36271-1-tommaso.merciai@amarulasolutions.com
State New
Headers
Series [v3] arm64: dts: imx8mm-evk: add pwm1/backlight support |

Commit Message

Tommaso Merciai April 13, 2022, 4:08 p.m. UTC 
Add pwm1/backlight support nodes for imx8mm_evk board.
Align with u-boot dts

References:
 - https://patchwork.ozlabs.org/project/uboot/patch/20220326111911.13720-9-tommaso.merciai@amarulasolutions.com/

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
---
Changes since v1:
 - Fix commit body
 - Enable pwm, backlight

Changes since v2:
 - Remove status okay from pwm1,backlight (enable as default)

 arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

Comments

Ahmad Fatoum April 13, 2022, 4:31 p.m. UTC | #1 
Hello Tomasso,

On 13.04.22 18:08, Tommaso Merciai wrote:
> Add pwm1/backlight support nodes for imx8mm_evk board.
> Align with u-boot dts
> 
> References:
>  - https://patchwork.ozlabs.org/project/uboot/patch/20220326111911.13720-9-tommaso.merciai@amarulasolutions.com/
> 
> Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
> ---
> Changes since v1:
>  - Fix commit body
>  - Enable pwm, backlight
> 
> Changes since v2:
>  - Remove status okay from pwm1,backlight (enable as default)
> 
>  arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> index 6d67df7692f1..c50d2cc3ca71 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> @@ -59,6 +59,14 @@ reg_usdhc2_vmmc: regulator-usdhc2 {
>  		enable-active-high;
>  	};
>  
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm1 0 5000000>;
> +		brightness-levels = <0 255>;
> +		num-interpolated-steps = <255>;
> +		default-brightness-level = <250>;
> +	};
> +
>  	ir-receiver {
>  		compatible = "gpio-ir-receiver";
>  		gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
> @@ -395,6 +403,11 @@ &wdog1 {
>  	status = "okay";
>  };
>  
> +&pwm1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_backlight>;

imx8mm.dtsi has &pwm1 { status = "disabled" };
Where is it enabled?

> +};
> +
>  &iomuxc {
>  	pinctrl_fec1: fec1grp {
>  		fsl,pins = <
> @@ -549,4 +562,10 @@ pinctrl_wdog: wdoggrp {
>  			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0x166
>  		>;
>  	};
> +
> +	pinctrl_backlight: backlightgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT	0x06
> +		>;
> +	};
>  };
Tommaso Merciai April 13, 2022, 9:35 p.m. UTC | #2 
On Wed, Apr 13, 2022 at 06:31:34PM +0200, Ahmad Fatoum wrote:
> Hello Tomasso,
> 
> On 13.04.22 18:08, Tommaso Merciai wrote:
> > Add pwm1/backlight support nodes for imx8mm_evk board.
> > Align with u-boot dts
> > 
> > References:
> >  - https://patchwork.ozlabs.org/project/uboot/patch/20220326111911.13720-9-tommaso.merciai@amarulasolutions.com/
> > 
> > Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
> > ---
> > Changes since v1:
> >  - Fix commit body
> >  - Enable pwm, backlight
> > 
> > Changes since v2:
> >  - Remove status okay from pwm1,backlight (enable as default)
> > 
> >  arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi | 19 +++++++++++++++++++
> >  1 file changed, 19 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > index 6d67df7692f1..c50d2cc3ca71 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > @@ -59,6 +59,14 @@ reg_usdhc2_vmmc: regulator-usdhc2 {
> >  		enable-active-high;
> >  	};
> >  
> > +	backlight: backlight {
> > +		compatible = "pwm-backlight";
> > +		pwms = <&pwm1 0 5000000>;
> > +		brightness-levels = <0 255>;
> > +		num-interpolated-steps = <255>;
> > +		default-brightness-level = <250>;
> > +	};
> > +
> >  	ir-receiver {
> >  		compatible = "gpio-ir-receiver";
> >  		gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
> > @@ -395,6 +403,11 @@ &wdog1 {
> >  	status = "okay";
> >  };
> >  
> > +&pwm1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_backlight>;
> 
> imx8mm.dtsi has &pwm1 { status = "disabled" };
> Where is it enabled?

Hi Ahmad,
Thanks for review, update in v4.

Tommaso
> 
> > +};
> > +
> >  &iomuxc {
> >  	pinctrl_fec1: fec1grp {
> >  		fsl,pins = <
> > @@ -549,4 +562,10 @@ pinctrl_wdog: wdoggrp {
> >  			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0x166
> >  		>;
> >  	};
> > +
> > +	pinctrl_backlight: backlightgrp {
> > +		fsl,pins = <
> > +			MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT	0x06
> > +		>;
> > +	};
> >  };
> 
> 
> -- 
> Pengutronix e.K.                           |                             |
> Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
> 31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
index 6d67df7692f1..c50d2cc3ca71 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
@@ -59,6 +59,14 @@  reg_usdhc2_vmmc: regulator-usdhc2 {
 		enable-active-high;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <250>;
+	};
+
 	ir-receiver {
 		compatible = "gpio-ir-receiver";
 		gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
@@ -395,6 +403,11 @@  &wdog1 {
 	status = "okay";
 };
 
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_backlight>;
+};
+
 &iomuxc {
 	pinctrl_fec1: fec1grp {
 		fsl,pins = <
@@ -549,4 +562,10 @@  pinctrl_wdog: wdoggrp {
 			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0x166
 		>;
 	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT	0x06
+		>;
+	};
 };