@@ -2,5 +2,4 @@
# (C) Copyright 2021 Amarula Solutions B.V.
obj-y := imx6ulz_smm_m2.o
-obj-$(CONFIG_XPL_BUILD) += spl.o ddr3l_timing_256m.o ddr3l_timing_128m.o
-
+obj-$(CONFIG_XPL_BUILD) += spl.o ddr3l_timing_512m.o ddr3l_timing_256m.o ddr3l_timing_128m.o
new file mode 100644
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "spl_mtypes.h"
+
+static const struct dram_cfg_param ddr_ddrc_cfg_512mb[] = {
+ //=============================================================================
+ // IOMUX
+ //=============================================================================
+ //DDR IO TYPE:
+ {0x020e04b4, 0x000C0000}, // IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE
+ {0x020e04ac, 0x00000000}, // IOMUXC_SW_PAD_CTL_GRP_DDRPKE
+
+ //CLOCK:
+ {0x020e027c, 0x00000028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK_0
+
+ //ADDRESS:
+ {0x020e0250, 0x00000028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS
+ {0x020e024c, 0x00000028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS
+ {0x020e0490, 0x00000028}, // IOMUXC_SW_PAD_CTL_GRP_ADDDS
+
+ //Control:
+ {0x020e0288, 0x000C0028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET
+ {0x020e0270, 0x00000000}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 - DSE can be configured using
+ // Group Control Register: IOMUXC_SW_PAD_CTL_GRP_CTLDS
+ {0x020e0260, 0x00000028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT0
+ {0x020e0264, 0x00000028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT1
+ {0x020e04a0, 0x00000028}, // IOMUXC_SW_PAD_CTL_GRP_CTLDS
+
+ //Data Strobes:
+ {0x020e0494, 0x00020000}, // IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL
+ {0x020e0280, 0x00000028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0
+ {0x020e0284, 0x00000028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1
+
+ //Data:
+ {0x020e04b0, 0x00020000}, // IOMUXC_SW_PAD_CTL_GRP_DDRMODE
+ {0x020e0498, 0x00000028}, // IOMUXC_SW_PAD_CTL_GRP_B0DS
+ {0x020e04a4, 0x00000028}, // IOMUXC_SW_PAD_CTL_GRP_B1DS
+
+ {0x020e0244, 0x00000028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0
+ {0x020e0248, 0x00000028}, // IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1
+
+ //=============================================================================
+ // DDR Controller Registers
+ //=============================================================================
+ // Manufacturer:ISSI
+ // Device Part Number:IS43TR16640BL-125JBLI
+ // Clock Freq.: 400MHz
+ // Density per CS in Gb: 2
+ // Chip Selects used:1
+ // Number of Banks:8
+ // Row address: 14
+ // Column address: 10
+ // Data bus width16
+ //=============================================================================
+ {0x021b001c, 0x00008000}, // MMDC0_MDSCR, set the Configuration request bit during
+ // MMDC set up
+
+ //=============================================================================
+ // Calibration setup.
+ //=============================================================================
+ {0x021b0800, 0xA1390003}, // DDR_PHY_P0_MPZQHWCTRL, enable both one-time & periodic
+ // HW ZQ calibration.
+
+ // For target board may need to run write leveling calibration to fine tune these settings.
+ {0x021b080c, 0x00000000}, //
+
+ //Read DQS Gating calibration
+ {0x021b083c, 0x01440140}, // MPDGCTRL0 PHY0
+
+ //Read calibration
+ {0x021b0848, 0x40403A3E}, // MPRDDLCTL PHY0
+
+ //Write calibration
+ {0x021b0850, 0x4040322A}, // MPWRDLCTL PHY0
+
+ //read data bit delay: 3 is the reccommended default value, although out of reset value is 0
+ {0x021b081c, 0x33333333}, // MMDC_MPRDDQBY0DL
+ {0x021b0820, 0x33333333}, // MMDC_MPRDDQBY1DL
+
+ //write data bit delay:
+ {0x021b082c, 0xF3333333}, // MMDC_MPWRDQBY0DL
+ {0x021b0830, 0xF3333333}, // MMDC_MPWRDQBY1DL
+
+ //DQS&CLK Duty Cycle
+ {0x021b08c0, 0x00944009}, // [MMDC_MPDCCR] MMDC Duty Cycle Control Register
+
+ // Complete calibration by forced measurement:
+ {0x021b08b8, 0x00000800}, // DDR_PHY_P0_MPMUR0, frc_msr
+ //=============================================================================
+ // Calibration setup end
+ //=============================================================================
+
+ //MMDC init:
+ {0x021b0004, 0x0002002D}, // MMDC0_MDPDC
+ {0x021b0008, 0x1B333030}, // MMDC0_MDOTC
+ {0x021b000c, 0x3F435333}, // MMDC0_MDCFG0
+ {0x021b0010, 0xB68E0B63}, // MMDC0_MDCFG1
+ {0x021b0014, 0x01FF00DB}, // MMDC0_MDCFG2
+
+ //MDMISC: RALAT kept to the high level of 5.
+ //MDMISC: consider reducing RALAT if your 528MHz board design allow that.
+ //Lower RALAT benefits:
+ //a. better operation at low frequency, for LPDDR2 freq < 100MHz, change RALAT to 3
+ //b. Small performence improvment
+ {0x021b0018, 0x00211740}, // MMDC0_MDMISC
+ {0x021b001c, 0x00008000}, // MMDC0_MDSCR set the Configuration request bit during
+ // MMDC set up
+ {0x021b002c, 0x000026D2}, // MMDC0_MDRWD
+ {0x021b0030, 0x00431023}, // MMDC0_MDOR
+ {0x021b0040, 0x0000004F}, // Chan0 CS0_END
+ {0x021b0000, 0x84180000}, // MMDC0_MDCTL
+
+ {0x021b0890, 0x00400000}, // MPPDCMPR2
+
+ //Mode register writes
+ {0x021b001c, 0x02808032}, // MMDC0_MDSCR, MR2 write, CS0
+ {0x021b001c, 0x00008033}, // MMDC0_MDSCR, MR3 write, CS0
+ {0x021b001c, 0x00048031}, // MMDC0_MDSCR, MR1 write, CS0
+ {0x021b001c, 0x15208030}, // MMDC0_MDSCR, MR0write, CS0
+ {0x021b001c, 0x04008040}, // MMDC0_MDSCR, ZQ calibration command sent to device on CS0
+
+ {0x021b0020, 0x00007800}, // MMDC0_MDREF
+
+ {0x021b0818, 0x00000227}, // DDR_PHY_P0_MPODTCTRL
+
+ {0x021b0004, 0x0002552D}, // MMDC0_MDPDC now SDCTL power down enabled
+
+ {0x021b0404, 0x00011006}, // MMDC0_MAPSR ADOPT power down enabled, MMDC will enter
+ // automatically to self-refresh while the number of idle
+ // cycle reached.
+
+ {0x021b001c, 0x00000000}, // MMDC0_MDSCR, clear this register (especially the
+ // configuration bit as initialization is complete)
+};
+
+struct dram_timing_info bsh_dram_timing_512mb = {
+ .ddrc_cfg = ddr_ddrc_cfg_512mb,
+ .ddrc_cfg_num = ARRAY_SIZE(ddr_ddrc_cfg_512mb),
+};
@@ -54,16 +54,19 @@ static void ddr_cfg_write(const struct dram_timing_info *dram_timing_info)
static void spl_dram_init(void)
{
/* Configure memory to maximum supported size for detection */
- ddr_cfg_write(&bsh_dram_timing_256mb);
+ ddr_cfg_write(&bsh_dram_timing_512mb);
/* Detect memory physically present */
- gd->ram_size = get_ram_size((void *)CFG_SYS_SDRAM_BASE, SZ_256M);
+ gd->ram_size = get_ram_size((void *)CFG_SYS_SDRAM_BASE, SZ_512M);
/* Reconfigure memory for actual detected size */
switch (gd->ram_size) {
- case SZ_256M:
+ case SZ_512M:
/* Already configured, nothing to do */
break;
+ case SZ_256M:
+ ddr_cfg_write(&bsh_dram_timing_256mb);
+ break;
case SZ_128M:
default:
ddr_cfg_write(&bsh_dram_timing_128mb);
@@ -20,6 +20,7 @@ struct dram_timing_info {
unsigned int ddrc_cfg_num;
};
+extern struct dram_timing_info bsh_dram_timing_512mb;
extern struct dram_timing_info bsh_dram_timing_256mb;
extern struct dram_timing_info bsh_dram_timing_128mb;