@@ -31,70 +31,209 @@ static void setup_iomux_uart(void)
imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
}
-static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
- .grp_addds = 0x00000028,
- .grp_ddrmode_ctl = 0x00020000,
- .grp_b0ds = 0x00000028,
- .grp_ctlds = 0x00000028,
- .grp_b1ds = 0x00000028,
- .grp_ddrpke = 0x00000000,
- .grp_ddrmode = 0x00020000,
- .grp_ddr_type = 0x000c0000,
+struct dram_cfg_param {
+ unsigned int reg;
+ unsigned int val;
};
-static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
- .dram_dqm0 = 0x00000028,
- .dram_dqm1 = 0x00000028,
- .dram_ras = 0x00000028,
- .dram_cas = 0x00000028,
- .dram_odt0 = 0x00000028,
- .dram_odt1 = 0x00000028,
- .dram_sdba2 = 0x00000000,
- .dram_sdclk_0 = 0x00000028,
- .dram_sdqs0 = 0x00000028,
- .dram_sdqs1 = 0x00000028,
- .dram_reset = 0x000c0028,
+struct dram_timing_info {
+ const struct dram_cfg_param *ddrc_cfg;
+ unsigned int ddrc_cfg_num;
};
-static struct mx6_mmdc_calibration mx6_mmcd_calib = {
- .p0_mpwldectrl0 = 0x00000000,
- .p0_mpwldectrl1 = 0x00100010,
- .p0_mpdgctrl0 = 0x414c014c,
- .p0_mpdgctrl1 = 0x00000000,
- .p0_mprddlctl = 0x40403a42,
- .p0_mpwrdlctl = 0x4040342e,
-};
+static const struct dram_cfg_param ddr_ddrc_cfg_128mb[] = {
+ /* IOMUX */
+
+ /* DDR IO Type: */
+ {0x020e04b4, 0x000C0000}, /* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
+ {0x020e04ac, 0x00000000}, /* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
+
+ /* Clock: */
+ {0x020e027c, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK_0 */
+
+ /* Address: */
+ {0x020e0250, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
+ {0x020e024c, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
+ {0x020e0490, 0x00000028}, /* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
+
+ /* Control: */
+ {0x020e0288, 0x000C0028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */
+
+ {0x020e0270, 0x00000000}, /*
+ * IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 - DSE can be configured
+ * using Group Control Register: IOMUXC_SW_PAD_CTL_GRP_CTLDS
+ */
+
+ {0x020e0260, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT0 */
+ {0x020e0264, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT1 */
+ {0x020e04a0, 0x00000028}, /* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+
+ /* Data Strobes: */
+ {0x020e0494, 0x00020000}, /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */
+ {0x020e0280, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0 */
+ {0x020e0284, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1 */
+
+ /* Data: */
+ {0x020e04b0, 0x00020000}, /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
+ {0x020e0498, 0x00000028}, /* IOMUXC_SW_PAD_CTL_GRP_B0DS */
+ {0x020e04a4, 0x00000028}, /* IOMUXC_SW_PAD_CTL_GRP_B1DS */
+
+ {0x020e0244, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
+ {0x020e0248, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
+
+ /*
+ * =============================================================================
+ * DDR Controller Registers
+ * =============================================================================
+ * Manufacturer:ISSI
+ * Device Part Number:IS43TR16640BL-125JBLI
+ * Clock Freq.: 400MHz
+ * Density per CS in Gb: 1
+ * Chip Selects used:1
+ * Number of Banks:8
+ * Row address: 13
+ * Column address: 10
+ * Data bus width16
+ * =============================================================================
+ */
+
+ {0x021b001c, 0x00008000}, /*
+ * MMDC0_MDSCR, set the Configuration request bit during
+ * MMDC set up
+ */
+
+ /*
+ * =============================================================================
+ * Calibration setup
+ * =============================================================================
+ */
+
+ {0x021b0800, 0xA1390003}, /*
+ * DDR_PHY_P0_MPZQHWCTRL, enable both one-time & periodic
+ * HW ZQ calibration.
+ */
+
+ /*
+ * For target board, may need to run write leveling calibration to fine tune these
+ * settings.
+ */
+ {0x021b080c, 0x00000000},
+
+ /* Read DQS Gating calibration */
+ {0x021b083c, 0x41480148}, /* MPDGCTRL0 PHY0 */
+
+ /* Read calibration */
+ {0x021b0848, 0x40403A3E}, /* MPRDDLCTL PHY0 */
+
+ /* Write calibration */
+ {0x021b0850, 0x4040362E}, /* MPWRDLCTL PHY0 */
+
+ /*
+ * Read data bit delay: 3 is the recommended default value, although out of reset
+ * value is 0
+ */
+ {0x021b081c, 0x33333333}, /* MMDC_MPRDDQBY0DL */
+ {0x021b0820, 0x33333333}, /* MMDC_MPRDDQBY1DL */
+
+ /* Write data bit delay: */
+ {0x021b082c, 0xF3333333}, /* MMDC_MPWRDQBY0DL */
+ {0x021b0830, 0xF3333333}, /* MMDC_MPWRDQBY1DL */
+
+ /* DQS&CLK Duty Cycle */
+ {0x021b08c0, 0x00944009}, /* [MMDC_MPDCCR] MMDC Duty Cycle Control Register */
+
+ /* Complete calibration by forced measurement: */
+ {0x021b08b8, 0x00000800}, /* DDR_PHY_P0_MPMUR0, frc_msr */
-static struct mx6_ddr_sysinfo ddr_sysinfo = {
- .dsize = 0,
- .cs1_mirror = 0,
- .cs_density = 32,
- .ncs = 1,
- .bi_on = 1,
- .rtt_nom = 1,
- .rtt_wr = 0,
- .ralat = 5,
- .walat = 1,
- .mif3_mode = 3,
- .rst_to_cke = 0x23, /* 33 cycles (JEDEC value for DDR3) - total of 500 us */
- .sde_to_rst = 0x10, /* 14 cycles (JEDEC value for DDR3) - total of 200 us */
- .refsel = 1,
- .refr = 3,
+ /*
+ * =============================================================================
+ * Calibration setup end
+ * =============================================================================
+ */
+
+ /* MMDC init: */
+ {0x021b0004, 0x0002002D}, /* MMDC0_MDPDC */
+ {0x021b0008, 0x1B333030}, /* MMDC0_MDOTC */
+ {0x021b000c, 0x2B2F52F3}, /* MMDC0_MDCFG0 */
+ {0x021b0010, 0xB66D0B63}, /* MMDC0_MDCFG1 */
+ {0x021b0014, 0x01FF00DB}, /* MMDC0_MDCFG2 */
+
+ /*
+ * MDMISC: RALAT kept to the high level of 5.
+ * MDMISC: consider reducing RALAT if your 528MHz board design allow that.
+ * Lower RALAT benefits:
+ * a. better operation at low frequency, for LPDDR2 freq < 100MHz, change RALAT to 3
+ * b. Small performance improvement
+ */
+ {0x021b0018, 0x00211740}, /* MMDC0_MDMISC */
+ {0x021b001c, 0x00008000}, /*
+ * MMDC0_MDSCR, set the Configuration request
+ * bit during MMDC set up
+ */
+ {0x021b002c, 0x000026D2}, /* MMDC0_MDRWD */
+ {0x021b0030, 0x002F1023}, /* MMDC0_MDOR */
+ {0x021b0040, 0x00000043}, /* Chan0 CS0_END */
+ {0x021b0000, 0x82180000}, /* MMDC0_MDCTL */
+
+ {0x021b0890, 0x00400000}, /* MPPDCMPR2 */
+
+ /* Mode register writes */
+ {0x021b001c, 0x02808032}, /* MMDC0_MDSCR, MR2 write, CS0 */
+ {0x021b001c, 0x00008033}, /* MMDC0_MDSCR, MR3 write, CS0 */
+ {0x021b001c, 0x00048031}, /* MMDC0_MDSCR, MR1 write, CS0 */
+ {0x021b001c, 0x15208030}, /* MMDC0_MDSCR, MR0write, CS0 */
+ {0x021b001c, 0x04008040}, /*
+ * MMDC0_MDSCR, ZQ calibration command sent to
+ * device on CS0
+ */
+ {0x021b0020, 0x00007800}, /* MMDC0_MDREF */
+
+ {0x021b0818, 0x00000227}, /* DDR_PHY_P0_MPODTCTRL */
+
+ {0x021b0004, 0x0002552D}, /* MMDC0_MDPDC now SDCTL power down enabled */
+
+ {0x021b0404, 0x00011006}, /*
+ * MMDC0_MAPSR ADOPT power down enabled,
+ * MMDC will enter automatically to self-refresh
+ * while the number of idle cycle reached.
+ */
+
+ {0x021b001c, 0x00000000}, /*
+ * MMDC0_MDSCR, clear this register
+ * (especially the configuration bit as initialization
+ * is complete)
+ */
};
-static struct mx6_ddr3_cfg mem_ddr = {
- .mem_speed = 1333,
- .density = 2,
- .width = 16,
- .banks = 8,
- .rowaddr = 13,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1350,
- .trcmin = 4950,
- .trasmin = 3600,
+static struct dram_timing_info dram_timing_128mb = {
+ .ddrc_cfg = ddr_ddrc_cfg_128mb,
+ .ddrc_cfg_num = ARRAY_SIZE(ddr_ddrc_cfg_128mb),
};
+static void ddr_cfg_write(const struct dram_timing_info *dram_timing_info)
+{
+ int i;
+ const struct dram_cfg_param *ddrc_cfg = dram_timing_info->ddrc_cfg;
+ const int ddrc_cfg_num = dram_timing_info->ddrc_cfg_num;
+
+ for (i = 0; i < ddrc_cfg_num; i++) {
+ debug("Writing 0x%x to register 0x%x\n", ddrc_cfg->val,
+ ddrc_cfg->reg);
+ writel(ddrc_cfg->val, ddrc_cfg->reg);
+ ddrc_cfg++;
+ }
+}
+
+static void spl_dram_init(void)
+{
+ struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
+
+ clrbits_le32(&mmdc0->mdctl, 1 << 31); /* clear SDE_0 */
+ clrbits_le32(&mmdc0->mdctl, 1 << 30); /* clear SDE_1 */
+
+ ddr_cfg_write(&dram_timing_128mb);
+}
+
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
@@ -108,20 +247,17 @@ static void ccgr_init(void)
writel(0xFFFFFFFF, &ccm->CCGR6);
}
-static void imx6ul_spl_dram_cfg(void)
-{
- mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
- mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
-}
-
void board_init_f(ulong dummy)
{
ccgr_init();
+
+ /* DDR initialization */
+ spl_dram_init();
+
arch_cpu_init();
timer_init();
setup_iomux_uart();
preloader_console_init();
- imx6ul_spl_dram_cfg();
}
void reset_cpu(void)