diff mbox series

[v2] ARM: dts: stm32: add U-Boot specific dtsi for stm32mp157f-dk2

Message ID 20260529153159.3944049-1-dario.binacchi@amarulasolutions.com
State New
Headers
Series [v2] ARM: dts: stm32: add U-Boot specific dtsi for stm32mp157f-dk2 |

Commit Message

Dario Binacchi May 29, 2026, 3:31 p.m. UTC 
The STM32MP157F-DK2 board is a direct derivative of the STM32MP157C-DK2.
As explained by ST [1], the "STM32MP157F-DK2 is assembled with latest
STM32MP15 RevZ cut which is the only one available for new product now.
The major differences in this 'F' variant SoC are the increased max
frequency of the Cortex-A7 cores and the correction of some HW bugs
(Device Rev.Z, see errata ES0438)".

On the software/architecture side, this variant utilizes SCMI (System
Control and Management Interface) for secure world resource management.
As a consequence, the underlying stm32mp15-scmi.dtsi explicitly deletes
several fixed clock nodes (such as clk_hse, clk_hsi, clk_lse, clk_lsi,
and clk_csi), making it impossible to include stm32mp157c-dk2-u-boot.dtsi
without triggering compilation errors due to these missing clock labels.

So let's introduce a dedicated stm32mp157f-dk2-u-boot.dtsi that directly
defines the fwu-mdata node. This provides the necessary FWU metadata
configuration required to allow automatic A/B bank selection, supported
for STM32MP15 boards by commit 560d8f32703f ("board: st: stm32mp15:
support dynamic A/B bank bootup").

[1] https://community.st.com/t5/stm32-mpus-products-and-hardware/i-m-wondering-what-s-the-difference-point-between-stm32mp157c/td-p/213460
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>

---

Changes in v2:
- Drop the inclusion of stm32mp157c-dk2-u-boot.dtsi to avoid compilation
  errors caused by deleted clock nodes in stm32mp15-scmi.dtsi.
- Directly define the fwu-mdata node in stm32mp157f-dk2-u-boot.dtsi to
  properly support automatic A/B bank selection.

 arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi

Comments

Patrice CHOTARD June 1, 2026, 9:09 a.m. UTC | #1 
On 5/29/26 17:31, Dario Binacchi wrote:
> The STM32MP157F-DK2 board is a direct derivative of the STM32MP157C-DK2.
> As explained by ST [1], the "STM32MP157F-DK2 is assembled with latest
> STM32MP15 RevZ cut which is the only one available for new product now.
> The major differences in this 'F' variant SoC are the increased max
> frequency of the Cortex-A7 cores and the correction of some HW bugs
> (Device Rev.Z, see errata ES0438)".
> 
> On the software/architecture side, this variant utilizes SCMI (System
> Control and Management Interface) for secure world resource management.
> As a consequence, the underlying stm32mp15-scmi.dtsi explicitly deletes
> several fixed clock nodes (such as clk_hse, clk_hsi, clk_lse, clk_lsi,
> and clk_csi), making it impossible to include stm32mp157c-dk2-u-boot.dtsi
> without triggering compilation errors due to these missing clock labels.
> 
> So let's introduce a dedicated stm32mp157f-dk2-u-boot.dtsi that directly
> defines the fwu-mdata node. This provides the necessary FWU metadata
> configuration required to allow automatic A/B bank selection, supported
> for STM32MP15 boards by commit 560d8f32703f ("board: st: stm32mp15:
> support dynamic A/B bank bootup").
> 
> [1] https://community.st.com/t5/stm32-mpus-products-and-hardware/i-m-wondering-what-s-the-difference-point-between-stm32mp157c/td-p/213460
> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
> 
> ---
> 
> Changes in v2:
> - Drop the inclusion of stm32mp157c-dk2-u-boot.dtsi to avoid compilation
>   errors caused by deleted clock nodes in stm32mp15-scmi.dtsi.
> - Directly define the fwu-mdata node in stm32mp157f-dk2-u-boot.dtsi to
>   properly support automatic A/B bank selection.
> 
>  arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi | 11 +++++++++++
>  1 file changed, 11 insertions(+)
>  create mode 100644 arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
> 
> diff --git a/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
> new file mode 100644
> index 000000000000..77805417bfa9
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
> @@ -0,0 +1,11 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2026 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
> + */
> +
> +/ {
> +	fwu-mdata {
> +		compatible = "u-boot,fwu-mdata-gpt";
> +		fwu-mdata-store = <&sdmmc1>;
> +	};
> +};

Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Thanks
Patrice

To unsubscribe from this group and stop receiving emails from it, send an email to linux-amarula+unsubscribe@amarulasolutions.com.
Patrice CHOTARD June 29, 2026, 7:29 a.m. UTC | #2 
On 5/29/26 17:31, Dario Binacchi wrote:
> The STM32MP157F-DK2 board is a direct derivative of the STM32MP157C-DK2.
> As explained by ST [1], the "STM32MP157F-DK2 is assembled with latest
> STM32MP15 RevZ cut which is the only one available for new product now.
> The major differences in this 'F' variant SoC are the increased max
> frequency of the Cortex-A7 cores and the correction of some HW bugs
> (Device Rev.Z, see errata ES0438)".
> 
> On the software/architecture side, this variant utilizes SCMI (System
> Control and Management Interface) for secure world resource management.
> As a consequence, the underlying stm32mp15-scmi.dtsi explicitly deletes
> several fixed clock nodes (such as clk_hse, clk_hsi, clk_lse, clk_lsi,
> and clk_csi), making it impossible to include stm32mp157c-dk2-u-boot.dtsi
> without triggering compilation errors due to these missing clock labels.
> 
> So let's introduce a dedicated stm32mp157f-dk2-u-boot.dtsi that directly
> defines the fwu-mdata node. This provides the necessary FWU metadata
> configuration required to allow automatic A/B bank selection, supported
> for STM32MP15 boards by commit 560d8f32703f ("board: st: stm32mp15:
> support dynamic A/B bank bootup").
> 
> [1] https://community.st.com/t5/stm32-mpus-products-and-hardware/i-m-wondering-what-s-the-difference-point-between-stm32mp157c/td-p/213460
> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
> 
> ---
> 
> Changes in v2:
> - Drop the inclusion of stm32mp157c-dk2-u-boot.dtsi to avoid compilation
>   errors caused by deleted clock nodes in stm32mp15-scmi.dtsi.
> - Directly define the fwu-mdata node in stm32mp157f-dk2-u-boot.dtsi to
>   properly support automatic A/B bank selection.
> 
>  arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi | 11 +++++++++++
>  1 file changed, 11 insertions(+)
>  create mode 100644 arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
> 
> diff --git a/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
> new file mode 100644
> index 000000000000..77805417bfa9
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
> @@ -0,0 +1,11 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2026 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
> + */
> +
> +/ {
> +	fwu-mdata {
> +		compatible = "u-boot,fwu-mdata-gpt";
> +		fwu-mdata-store = <&sdmmc1>;
> +	};
> +};

Hi Dario

What about including stm32mp157c-dk2-u-boot.dtsi instead of defining fwu-mdata node ?

Thanks
Patrice

To unsubscribe from this group and stop receiving emails from it, send an email to linux-amarula+unsubscribe@amarulasolutions.com.
Dario Binacchi July 2, 2026, 1 p.m. UTC | #3 
Hi Patrice

On Mon, Jun 29, 2026 at 9:29 AM Patrice CHOTARD
<patrice.chotard@foss.st.com> wrote:
>
>
>
> On 5/29/26 17:31, Dario Binacchi wrote:
> > The STM32MP157F-DK2 board is a direct derivative of the STM32MP157C-DK2.
> > As explained by ST [1], the "STM32MP157F-DK2 is assembled with latest
> > STM32MP15 RevZ cut which is the only one available for new product now.
> > The major differences in this 'F' variant SoC are the increased max
> > frequency of the Cortex-A7 cores and the correction of some HW bugs
> > (Device Rev.Z, see errata ES0438)".
> >
> > On the software/architecture side, this variant utilizes SCMI (System
> > Control and Management Interface) for secure world resource management.
> > As a consequence, the underlying stm32mp15-scmi.dtsi explicitly deletes
> > several fixed clock nodes (such as clk_hse, clk_hsi, clk_lse, clk_lsi,
> > and clk_csi), making it impossible to include stm32mp157c-dk2-u-boot.dtsi
> > without triggering compilation errors due to these missing clock labels.
> >
> > So let's introduce a dedicated stm32mp157f-dk2-u-boot.dtsi that directly
> > defines the fwu-mdata node. This provides the necessary FWU metadata
> > configuration required to allow automatic A/B bank selection, supported
> > for STM32MP15 boards by commit 560d8f32703f ("board: st: stm32mp15:
> > support dynamic A/B bank bootup").
> >
> > [1] https://community.st.com/t5/stm32-mpus-products-and-hardware/i-m-wondering-what-s-the-difference-point-between-stm32mp157c/td-p/213460
> > Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
> >
> > ---
> >
> > Changes in v2:
> > - Drop the inclusion of stm32mp157c-dk2-u-boot.dtsi to avoid compilation
> >   errors caused by deleted clock nodes in stm32mp15-scmi.dtsi.
> > - Directly define the fwu-mdata node in stm32mp157f-dk2-u-boot.dtsi to
> >   properly support automatic A/B bank selection.
> >
> >  arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi | 11 +++++++++++
> >  1 file changed, 11 insertions(+)
> >  create mode 100644 arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
> >
> > diff --git a/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
> > new file mode 100644
> > index 000000000000..77805417bfa9
> > --- /dev/null
> > +++ b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
> > @@ -0,0 +1,11 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright (C) 2026 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
> > + */
> > +
> > +/ {
> > +     fwu-mdata {
> > +             compatible = "u-boot,fwu-mdata-gpt";
> > +             fwu-mdata-store = <&sdmmc1>;
> > +     };
> > +};
>
> Hi Dario
>
> What about including stm32mp157c-dk2-u-boot.dtsi instead of defining fwu-mdata node ?

This was actually the approach used in v1. However, as you pointed out in the
v1 thread [1], it does not build because stm32mp15-scmi.dtsi removes the
clk_hse, clk_hsi, clk_lse, clk_lsi and clk_csi labels referenced by
stm32mp157c-dk2-u-boot.dtsi.

That's why I dropped the include in v2 and defined only the fwu-mdata node
locally.

Or am I perhaps missing something?

[1] https://patchwork.ozlabs.org/project/uboot/patch/20260512071157.564081-1-dario.binacchi@amarulasolutions.com/

Thanks and regards,
Dario

>
> Thanks
> Patrice
Patrice CHOTARD July 3, 2026, 12:40 p.m. UTC | #4 
On 7/2/26 15:00, Dario Binacchi wrote:
> Hi Patrice
> 
> On Mon, Jun 29, 2026 at 9:29 AM Patrice CHOTARD
> <patrice.chotard@foss.st.com> wrote:
>>
>>
>>
>> On 5/29/26 17:31, Dario Binacchi wrote:
>>> The STM32MP157F-DK2 board is a direct derivative of the STM32MP157C-DK2.
>>> As explained by ST [1], the "STM32MP157F-DK2 is assembled with latest
>>> STM32MP15 RevZ cut which is the only one available for new product now.
>>> The major differences in this 'F' variant SoC are the increased max
>>> frequency of the Cortex-A7 cores and the correction of some HW bugs
>>> (Device Rev.Z, see errata ES0438)".
>>>
>>> On the software/architecture side, this variant utilizes SCMI (System
>>> Control and Management Interface) for secure world resource management.
>>> As a consequence, the underlying stm32mp15-scmi.dtsi explicitly deletes
>>> several fixed clock nodes (such as clk_hse, clk_hsi, clk_lse, clk_lsi,
>>> and clk_csi), making it impossible to include stm32mp157c-dk2-u-boot.dtsi
>>> without triggering compilation errors due to these missing clock labels.
>>>
>>> So let's introduce a dedicated stm32mp157f-dk2-u-boot.dtsi that directly
>>> defines the fwu-mdata node. This provides the necessary FWU metadata
>>> configuration required to allow automatic A/B bank selection, supported
>>> for STM32MP15 boards by commit 560d8f32703f ("board: st: stm32mp15:
>>> support dynamic A/B bank bootup").
>>>
>>> [1] https://community.st.com/t5/stm32-mpus-products-and-hardware/i-m-wondering-what-s-the-difference-point-between-stm32mp157c/td-p/213460
>>> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
>>>
>>> ---
>>>
>>> Changes in v2:
>>> - Drop the inclusion of stm32mp157c-dk2-u-boot.dtsi to avoid compilation
>>>   errors caused by deleted clock nodes in stm32mp15-scmi.dtsi.
>>> - Directly define the fwu-mdata node in stm32mp157f-dk2-u-boot.dtsi to
>>>   properly support automatic A/B bank selection.
>>>
>>>  arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi | 11 +++++++++++
>>>  1 file changed, 11 insertions(+)
>>>  create mode 100644 arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
>>>
>>> diff --git a/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
>>> new file mode 100644
>>> index 000000000000..77805417bfa9
>>> --- /dev/null
>>> +++ b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
>>> @@ -0,0 +1,11 @@
>>> +// SPDX-License-Identifier: GPL-2.0+
>>> +/*
>>> + * Copyright (C) 2026 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
>>> + */
>>> +
>>> +/ {
>>> +     fwu-mdata {
>>> +             compatible = "u-boot,fwu-mdata-gpt";
>>> +             fwu-mdata-store = <&sdmmc1>;
>>> +     };
>>> +};
>>
>> Hi Dario
>>
>> What about including stm32mp157c-dk2-u-boot.dtsi instead of defining fwu-mdata node ?
> 
> This was actually the approach used in v1. However, as you pointed out in the
> v1 thread [1], it does not build because stm32mp15-scmi.dtsi removes the
> clk_hse, clk_hsi, clk_lse, clk_lsi and clk_csi labels referenced by
> stm32mp157c-dk2-u-boot.dtsi.
> 
> That's why I dropped the include in v2 and defined only the fwu-mdata node
> locally.
> 
> Or am I perhaps missing something?

Hi Dario

Sorry, you are right, it's just following an internal discussion with Patrick and i totally forgot your 
v1 implementation already included  stm32mp157c-dk2-u-boot.dtsi and has compilatioj issue.

Patrice


> 
> [1] https://patchwork.ozlabs.org/project/uboot/patch/20260512071157.564081-1-dario.binacchi@amarulasolutions.com/
> 
> Thanks and regards,
> Dario
> 
>>
>> Thanks
>> Patrice
> 
> 
> 

To unsubscribe from this group and stop receiving emails from it, send an email to linux-amarula+unsubscribe@amarulasolutions.com.
Patrice CHOTARD Sept. 1, 2026, 11:51 a.m. UTC | #5 
On 7/3/26 14:40, Patrice CHOTARD wrote:
> 
> 
> On 7/2/26 15:00, Dario Binacchi wrote:
>> Hi Patrice
>>
>> On Mon, Jun 29, 2026 at 9:29 AM Patrice CHOTARD
>> <patrice.chotard@foss.st.com> wrote:
>>>
>>>
>>>
>>> On 5/29/26 17:31, Dario Binacchi wrote:
>>>> The STM32MP157F-DK2 board is a direct derivative of the STM32MP157C-DK2.
>>>> As explained by ST [1], the "STM32MP157F-DK2 is assembled with latest
>>>> STM32MP15 RevZ cut which is the only one available for new product now.
>>>> The major differences in this 'F' variant SoC are the increased max
>>>> frequency of the Cortex-A7 cores and the correction of some HW bugs
>>>> (Device Rev.Z, see errata ES0438)".
>>>>
>>>> On the software/architecture side, this variant utilizes SCMI (System
>>>> Control and Management Interface) for secure world resource management.
>>>> As a consequence, the underlying stm32mp15-scmi.dtsi explicitly deletes
>>>> several fixed clock nodes (such as clk_hse, clk_hsi, clk_lse, clk_lsi,
>>>> and clk_csi), making it impossible to include stm32mp157c-dk2-u-boot.dtsi
>>>> without triggering compilation errors due to these missing clock labels.
>>>>
>>>> So let's introduce a dedicated stm32mp157f-dk2-u-boot.dtsi that directly
>>>> defines the fwu-mdata node. This provides the necessary FWU metadata
>>>> configuration required to allow automatic A/B bank selection, supported
>>>> for STM32MP15 boards by commit 560d8f32703f ("board: st: stm32mp15:
>>>> support dynamic A/B bank bootup").
>>>>
>>>> [1] https://community.st.com/t5/stm32-mpus-products-and-hardware/i-m-wondering-what-s-the-difference-point-between-stm32mp157c/td-p/213460
>>>> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
>>>>
>>>> ---
>>>>
>>>> Changes in v2:
>>>> - Drop the inclusion of stm32mp157c-dk2-u-boot.dtsi to avoid compilation
>>>>   errors caused by deleted clock nodes in stm32mp15-scmi.dtsi.
>>>> - Directly define the fwu-mdata node in stm32mp157f-dk2-u-boot.dtsi to
>>>>   properly support automatic A/B bank selection.
>>>>
>>>>  arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi | 11 +++++++++++
>>>>  1 file changed, 11 insertions(+)
>>>>  create mode 100644 arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
>>>>
>>>> diff --git a/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
>>>> new file mode 100644
>>>> index 000000000000..77805417bfa9
>>>> --- /dev/null
>>>> +++ b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
>>>> @@ -0,0 +1,11 @@
>>>> +// SPDX-License-Identifier: GPL-2.0+
>>>> +/*
>>>> + * Copyright (C) 2026 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
>>>> + */
>>>> +
>>>> +/ {
>>>> +     fwu-mdata {
>>>> +             compatible = "u-boot,fwu-mdata-gpt";
>>>> +             fwu-mdata-store = <&sdmmc1>;
>>>> +     };
>>>> +};
>>>
>>> Hi Dario
>>>
>>> What about including stm32mp157c-dk2-u-boot.dtsi instead of defining fwu-mdata node ?
>>
>> This was actually the approach used in v1. However, as you pointed out in the
>> v1 thread [1], it does not build because stm32mp15-scmi.dtsi removes the
>> clk_hse, clk_hsi, clk_lse, clk_lsi and clk_csi labels referenced by
>> stm32mp157c-dk2-u-boot.dtsi.
>>
>> That's why I dropped the include in v2 and defined only the fwu-mdata node
>> locally.
>>
>> Or am I perhaps missing something?
> 
> Hi Dario
> 
> Sorry, you are right, it's just following an internal discussion with Patrick and i totally forgot your 
> v1 implementation already included  stm32mp157c-dk2-u-boot.dtsi and has compilatioj issue.
> 
> Patrice
> 
> 
>>
>> [1] https://patchwork.ozlabs.org/project/uboot/patch/20260512071157.564081-1-dario.binacchi@amarulasolutions.com/
>>
>> Thanks and regards,
>> Dario
>>
>>>
>>> Thanks
>>> Patrice
>>
>>
>>
> 
> _______________________________________________
> Uboot-stm32 mailing list
> Uboot-stm32@st-md-mailman.stormreply.com
> https://st-md-mailman.stormreply.com/mailman/listinfo/uboot-stm32
Applied to u-boot-stm32/next

Thanks
Patrice

To unsubscribe from this group and stop receiving emails from it, send an email to linux-amarula+unsubscribe@amarulasolutions.com.
diff mbox series

Patch

diff --git a/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
new file mode 100644
index 000000000000..77805417bfa9
--- /dev/null
+++ b/arch/arm/dts/stm32mp157f-dk2-u-boot.dtsi
@@ -0,0 +1,11 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2026 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
+ */
+
+/ {
+	fwu-mdata {
+		compatible = "u-boot,fwu-mdata-gpt";
+		fwu-mdata-store = <&sdmmc1>;
+	};
+};