[v6,00/16] arm64: support Engicam MicroGEA-STM32MP257-RMM board
mbox series

Message ID 20260630092628.1695560-1-dario.binacchi@amarulasolutions.com
Headers show
Series
  • arm64: support Engicam MicroGEA-STM32MP257-RMM board
Related show

Message

Dario Binacchi June 30, 2026, 9:24 a.m. UTC 
This series adds initial support for the Engicam MicroGEA-STM32MP257-RMM
board based on the MicroGEA-STM32MP257 SoM.

The support includes device tree descriptions for both the SoM and the
carrier board, together with the required pinctrl definitions for the
peripherals used.

The series also updates the arm64 defconfig accordingly.

Changes in v6:
- Update arch/arm64/configs/defconfig to match the current upstream defconfig
  after merge window changes (no functional changes).

Changes in v5:
- Add patch 2/16 arm64: dts: st: add power-domains to sdmmc1 on stm32mp231
- Add patch 3/16 arm64: dts: st: add power-domains to sdmmc1 on stm32mp251
- Increase slew-rate to <1> of ltdc pins to support the 27 MHz pixel clock
  and prevent timing violations.
- Change SDMMC2_CK pin bias from pull-up to bias-disable to avoid signal
  integrity issues on the clock line
- Fix touchscreen resolution to 480x854
- Fix SPI1 CS0 polarity to GPIO_ACTIVE_LOW

Changes in v4:
- Drop inclusion of stm32mp25xf.dtsi from stm32mp257-engicam-microgea.dtsi

Changes in v3:
- Add power-domains property in the SDMMC2 node.
- Drop patch "arm64: defconfig: cleanup the defconfig"

Changes in v2:
- Add Acked-by of Conor Dooley for patch 0/1 "dt-bindings: arm: stm32:
  support Engicam MicroGEA-STM32MP257-RMM board"
- Add resets property to dts CAN node. Suggested by Sashiko.
- Drop the clocks property from the sai1 node in stm32mp257-engicam-microgea-rmm.dts
  to avoid overriding the peripheral bus clock reference defined in the base
  SoC device tree. Suggested by Sashiko.
- Reference the existing labeled nodes directly at the root level using
  &sai1a and &sai1b in stm32mp257-engicam-microgea-rmm.dts instead of
  redefining the entire node structure and redeclaring the labels. Suggested by Sashiko.
- Drop the #clock-cells property from sai1a and remove the reference to sai1a from
  the clocks array in sai1b, relying strictly on the st,sync property to handle
  internal synchronization.

Dario Binacchi (16):
  dt-bindings: arm: stm32: support Engicam MicroGEA-STM32MP257-RMM board
  arm64: dts: st: add power-domains to sdmmc1 on stm32mp231
  arm64: dts: st: add power-domains to sdmmc1 on stm32mp251
  arm64: dts: st: add SDMMC2 support on stm32mp25
  arm64: dts: st: add CAN1 support on stm32mp25
  arm64: dts: st: add i2c1 pins for stm32mp25
  arm64: dts: st: add ltdc pins for stm32mp25
  arm64: dts: st: add can1 pins for stm32mp25
  arm64: dts: st: add pwm2/pwm4 pins for stm32mp25
  arm64: dts: st: add sai1 pins for stm32mp25
  arm64: dts: st: add sdmmc2 pins for stm32mp25
  arm64: dts: st: add spi1 pins for stm32mp25
  arm64: dts: st: add usart1 pins for stm32mp25
  arm64: dts: st: support Engicam MicroGEA-STM32MP257 SoM
  arm64: dts: st: support Engicam MicroGEA-STM32MP257-RMM board
  arm64: defconfig: enable configs for Engicam  MicroGEA-STM32MP257-RMM

 .../devicetree/bindings/arm/stm32/stm32.yaml  |   7 +
 arch/arm64/boot/dts/st/Makefile               |   1 +
 arch/arm64/boot/dts/st/stm32mp231.dtsi        |   1 +
 arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi | 328 ++++++++++++++++++
 arch/arm64/boot/dts/st/stm32mp251.dtsi        |  17 +
 arch/arm64/boot/dts/st/stm32mp253.dtsi        |  16 +
 .../st/stm32mp257-engicam-microgea-rmm.dts    | 319 +++++++++++++++++
 .../dts/st/stm32mp257-engicam-microgea.dtsi   |  63 ++++
 arch/arm64/configs/defconfig                  |   4 +
 9 files changed, 756 insertions(+)
 create mode 100644 arch/arm64/boot/dts/st/stm32mp257-engicam-microgea-rmm.dts
 create mode 100644 arch/arm64/boot/dts/st/stm32mp257-engicam-microgea.dtsi