diff mbox series

[1/9] arm64: dts: imx8mn-bsh-smm-s2-common: Define suspend voltage threshold

Message ID 20250514082507.1983849-2-dario.binacchi@amarulasolutions.com
State New
Headers
Series DTS updates for BSH SMM S2[PRO] boards |

Commit Message

Dario Binacchi May 14, 2025, 8:24 a.m. UTC 
From: Michael Trimarchi <michael@amarulasolutions.com>

Voltage threshold should be adjust according to the worst case.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
---

 .../boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi  | 11 +++++++++++
 1 file changed, 11 insertions(+)

Comments

Matti Vaittinen May 15, 2025, 8:52 a.m. UTC | #1 
On 14/05/2025 11:24, Dario Binacchi wrote:
> From: Michael Trimarchi <michael@amarulasolutions.com>
> 
> Voltage threshold should be adjust according to the worst case.

I would love to understand why these voltages are set.

Could you please explain a bit further why this change is done. What 
worst case? What happens if voltages aren't adjusted? What is the 
current voltage (before this patch is applied?).

> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
> ---
> 
>   .../boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi  | 11 +++++++++++
>   1 file changed, 11 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi
> index bbb07c650da9..5a1ec2f6a552 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi
> @@ -105,6 +105,12 @@ buck1_reg: BUCK1 {
>   				regulator-boot-on;
>   				regulator-always-on;
>   				regulator-ramp-delay = <1250>;
> +
> +				/* enable autosuspend threshold */
> +				rohm,dvs-run-voltage = <850000>;
> +				rohm,dvs-idle-voltage = <850000>;
> +				rohm,dvs-suspend-voltage = <850000>;
> +				rohm,no-regulator-enable-control;

The commit message does not explain why the software control of the 
regulator's enable state is changed? Maybe this should be in the 2/9?

>   			};
>   
>   			buck2_reg: BUCK2 {
> @@ -115,6 +121,11 @@ buck2_reg: BUCK2 {
>   				regulator-boot-on;
>   				regulator-always-on;
>   				regulator-ramp-delay = <1250>;
> +
> +				/* enable autosuspend threshold */
> +				rohm,dvs-run-voltage = <960000>;
> +				rohm,dvs-idle-voltage = <860000>;
> +				rohm,no-regulator-enable-control;

same here?

>   			};
>   
>   			buck3_reg: BUCK3 {

Yours,
	-- Matti

To unsubscribe from this group and stop receiving emails from it, send an email to linux-amarula+unsubscribe@amarulasolutions.com.
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi
index bbb07c650da9..5a1ec2f6a552 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi
@@ -105,6 +105,12 @@  buck1_reg: BUCK1 {
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <1250>;
+
+				/* enable autosuspend threshold */
+				rohm,dvs-run-voltage = <850000>;
+				rohm,dvs-idle-voltage = <850000>;
+				rohm,dvs-suspend-voltage = <850000>;
+				rohm,no-regulator-enable-control;
 			};
 
 			buck2_reg: BUCK2 {
@@ -115,6 +121,11 @@  buck2_reg: BUCK2 {
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <1250>;
+
+				/* enable autosuspend threshold */
+				rohm,dvs-run-voltage = <960000>;
+				rohm,dvs-idle-voltage = <860000>;
+				rohm,no-regulator-enable-control;
 			};
 
 			buck3_reg: BUCK3 {